46005 Simpson, 46005 Datasheet - Page 4

• Manufacturer Part Number: 46005
• Description: Measuring Wheel With Tire
• Manufacturer: Simpson
• Type: 12 In Measuring Wheelr

Specifications of 46005

• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Accessory Type: Measuring Wheel
• Application: For textiles, medium textures
• Equipment Type: Totalizer Counter
• Modes: Count/Direction, Add/Add, Add/Subtract, Subtract/Subtract, Quadrature and Reverse Quadrature.
• For Use With: S660 Preset Totalizer Counter
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

The Excitation Module can supply 12VDC at up to 100mA for external
sensors or encoders. This excitation is isolated from the counter internal
logic supply.
When using sensors or encoders that do not have a signal return or imply
a signal return that is in common with the supply voltage, a common
attachment that ties the excitation supply to the logic input common may
be required.
The Single and Dual Relay modules can activate circuit loads of up to 5
amps at 250VAC. A Form C configuration allows use of normally-open
(NO) and normally-closed (NC) circuit action.
Only the output 1 channel is implemented in the single relay module.
A Simpson Encoder and Counter are to be used to measure and cut
raw material to length. A dual- speed motor is used to allow selection of
high speed, low speed and stop. A pneumatic shear allows the material
to be cut.
Material is initially to be fed at high speed. In the final six inches, low
speed will be used. When the desired length is reached, the motor will
be temporarily stopped and the shear activated for two seconds. The
feed and cut cycle then resumes for a new piece.
Machine Specifications
Motor and Control:
Shear Specifications:
Mechanical:
*Default Setting
Menu Category
Excitation Output
Programming (Cont’d)
Single and Dual Relay Modules
Application Example
Reset SETUP
End
Motor runs in low speed when 120VAC applied
to Run-Lo terminal. Hi Speed selected with
120VAC to Run-Hi Terminal. Maximum control
current is 3 amps at either terminal. Hi speed =
1725 RPM, Lo speed = 430 RPM.
The pneumatic cutting blade is activated by
applying 120VAC (0.5 amp maximum) to a con-
trol valve.
A motor reducer and drive pulley result in 1” of
linear travel for every five motor revolutions.
Parameter Name
RstBtn
PonRst
Choices/Format
enable
disabl
No
Yes
*
*
Product Ordering Information
In the application example, a Simpson S660 Preset Totalizing Counter
with a 120VAC power supply, Quadrature Input, Dual Relay Output, and
12VDC excitation is used (catalog no. S660-1-2-2-1-0). The encoder
used is the SE Quadrature Encoder with 600 pulses-per-revolution (SE-
600).
durameter non-marking tires (46005) are also required.
Process:
Display:
Description
Reset Button Enable or disable front panel reset button.
Power On Reset select whether count reset event will occur at
power-up.
Exit Programming Menu
Single Relay Module
An encoder chariot (46012) and 12” measuring wheel with 83A
1
250V
SINGLE RELAY
N.O.
N.C.
COM
ISO+12V
ISOCOM
5A
!
Minimum and maximum piece length will be 12
inches and 6000 inches (500 feet) respectively.
Material is a light colored textile, so skidding by
measuring device is to be avoided.
Desired display and entry of lengths is in inches
with two decimal places (1/100 inch resolution).
i.e. The customer would like to enter 0.25 inch
increments.
EXCITATION
__
---
+
_
Denotes module
position 2 at rear of
counter
Denotes module
position 5 at
rear of counter
12 VDC, 100 mA max
Dual Relay Module
1
2
250V
N.O.
N.C.
COM
COM
N.C.
N.O.
RELAYS
5A
!