OPBT2QD BANNER ENGINEERING, OPBT2QD Datasheet - Page 8

• Manufacturer Part Number: OPBT2QD
• Description: Proximity Sensor
• Manufacturer: BANNER ENGINEERING

Specifications of OPBT2QD

• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Supply Voltage Max: 30VDC
• Switch Terminals: Quick Connect
• Supply Voltage Min: 10VDC
• Operating Temperature Min: -40°C
• Operating Temperature Max: 70°C
• Sensor Output: NPN/PNP

#10 Screw
Clearance (4)
OMNI-BEAM Sensor Heads
page
OMNI-BEAM Sensor with Attached Cable
76.2 mm w/DC Power Block
(3.00")
98.6mm w/AC Power Block
(3.88")
Supply Voltage and Current
Output Response Time
Adjustments
Indicators
Construction
Environmental Rating
Operating Temperature
Certifications
Cross-hole design for front,
back, or side mounting
Transparent Cover (Gasketed)
View: D.A.T.A. Lights
Remove to Access:
8
Sensing Status
Output Load
Sensitivity (Gain) Adjustment
Logic Timing Adjustments
44.5 mm (1.75")
57.4 mm w/DC
79.8 mm w/AC
7.1 mm
(0.28")
(2.26")
(3.14")
2 m ( 6.5' Cable)
OMNI-BEAM Dimensions – Sensor Head Shown Assembled to Power Block
30.0 mm
(1.18")
Supplied by OMNI-BEAM power block
See individual sensing heads for response times (page 2)
200 millisecond delay on power-up: outputs are non-conducting during this time.
OMNI-BEAM sensor heads are field-programmable for four operating parameters. A set of four
programming DIP switches is located at the base of the sensor head and is accessible with the sensor
head removed from the power block (see page 4).
Switch #1 selects the amount of sensing hysteresis
Switch #2 selects the alarm output configuration
Switch #3 selects LIGHT operate (switch #3 OFF) or DARK operate (switch #3 ON)
Switch #4 selects the STANDARD (switch #4 OFF) or FINE (switch #4 ON) scale factor for the D.A.T.A.
light signal strength indicator array
15-turn slotted brass screw Gain (sensitivity) adjustment potentiometer (clutched at both ends of travel)
Sense and Load indicator LEDs are located on the top of the sensor head on either side of the D.A.T.A. array.
Sense LED indicates when a target has been sensed
Load LED lights whenever the load output is energized
Also, Banner’s exclusive D.A.T.A. sensor self-diagnostic system located on the top of the sensor head
warns of marginal sensing conditions usually before a sensing failure occurs (except on model OSBFAC).
Sensor heads are molded of rugged reinforced thermoplastic polyester; top view window is LEXAN
polycarbonate; acrylic lenses; stainless steel hardware
Meets NEMA standards 1, 2, 3, 3S, 4, 12, and 13; IEC IP66 when assembled to power block
Temperature: -40° to +70°C (-40° to +158°F)
Maximum relative humidity: 90% at 50°C (non-condensing)
LEXAN
* 61.7 mm (2.43") for OSBCV, CVG, CVB
60.5 mm (2.38") for OSBF, FV, FVG, FVB, FX, EF, RF, FAC
59.8 mm (2.35") for OSBFP, FPG, FPB
30.0 mm
(1.18")
®
OMNI-BEAM Sensor Head Specifications
is a registered trademark of General Electric Company
54.6 mm*
(2.15")
38.1 mm w/DC
60.5 mm w/AC
7.1 mm
(0.28")
(1.50")
(2.38")
External Thread
Internal Thread
(1/2-14NPSM)
5.6 mm (0.22")
M30 X 1.5
Lens
Centerline
Hex Nut
Supplied
Mini-Style
14 mm (0.6")
OMNI-BEAM Sensor with Quick Disconnect
Mini-style QD Connector
15 mm (0.6")
Euro-style QD Connector
Euro-Style
®