62M15-L4-020CH Grayhill Inc, 62M15-L4-020CH Datasheet - Page 2

• Manufacturer Part Number: 62M15-L4-020CH
• Description: 62M15-L4-020CH Eg
• Manufacturer: Grayhill Inc

SPECIFICATIONS
Environmental Specifications
Operating Temperature Range: -40
Storage Temperature Range: -55
Humidity: 96 hours at 90-95% humidity
at 40
Mechanical Vibration: Harmonic motion with
amplitude of 15 g, within a varied frequency of
10 to 2000 Hz
Mechanical Shock:
Test 1: 100 g for 6 ms half-sine wave with a
velocity change of 12.3 ft/sec
Test 2: 100 g for 6 ms sawtooth wave with a
velocity change of 9.7 ft/sec
Rotary Electrical and
Mechanical Specifications
Operating Voltage: 5.00±.25 Vdc
Supply Current: 30 mA maximum at 5 Vdc
Output: Open collector phototransistor,
external pull-up resistors are required
Output Code: Two-bit quadrature, channel A
leads channel B by 90
clockwise rotation of the shaft
Logic Output Characteristics:
Logic high signal shall be no less
than 3.0 Vdc
Logic low signal shall be no greater
than 1.0 Vdc
Minimum Sink Current: 2.0 mA
Power Consumption: 150 mW maximum
Mechanical Life: 10 million rotational cycles of
operation. One cycle is a rotation through all
positions and a full return
WAVEFORM AND TRUTH TABLE
Available from your local Grayhill Component Distributor. For pricing and discounts, contact a local Sales Office, an authorized local
561 Hillgrove Avenue • LaGrange, IL 60525 • Phone: [phone] • Fax: [phone] • www.grayhill.com
Distributor, or Grayhill.
0
62MXX-XX-XXXX
C
OUTPUT
OUTPUT
Grayhill Optical Encoders
A
B
HIGH
LOW
HIGH
LOW
0
1
electrically during
2
POSITION NUMBER
3
0
C to 100
0
C to 85
4
Pushbutton Option: 0=Non-Pushbutton, 2 = 200 grams, 3 = 300 grams, 4 = 510
grams
Termination: CH =.100 Cable with connector, SH = Cable with Stripped-End, PH = Pin Header
Cable Lenght: 020 thru 250 in 1/2” increments (three digits are eliminated if pinned termination is
required) Example: 060 = 6.0” cable, 135 = 13.5 cable.
Angle of Throw: 22 = 22.5
detent positions
Rotational Torque: H=High Torque (2.00 in-oz), M=Medium Torque (1.00 in-oz), L=Low Torque (.50 in-oz)
Series
5
0
0
C
C
6
Average Rotational Torque: H=2.00 in-oz
M=1.00 in-oz, L=.50 in-oz
Mounting Torque: 15 in-oz maximum
Shaft Pull-Out Force: 45 lbs minimum
Terminal Strength: 15 lbs minimum
terminal pull-out force for cable or header
termination
Solderability: 95% free of pin holes and
voids
Pushbutton Electrical and
Mechanical Specifications
Rating: 10 mA at 5 Vdc
Contact Resistance: <10 ohms
Life: 3 million actuations minimum
Contact Bounce: <4 ms make,<10 ms
break
Actuation Force: 2=200±75 grams,
3=300±90 grams, 4=510±150 grams
Shaft Travel: .25 ± .010 inches
Materials and Finishes
Bushing: Zinc Diecast, Cadmium Plated
per QQP-416, Class II, Type II
Insert Molded into 25% Glass Reinforced
Nylon Zytel FR-50
Shaft: NdFeB XE-3594 over Grilamid
LV23H
Stator: Powdered Metal per F-0000-20
0
for code change and 16 detent positions, 15 = 15
• Indicates logic high; blank indicates logic
low. Code repeats every 4 positions.
Position
1
2
3
4
Series 62M
Clockwise Rotation
Output A
•
•
Through Bolts: 305 Stainless Steel
Through Bolts Nuts: Stainless Steel
Spacer Washer: Brass
Snap Dome: Stainless Steel
Printed Circuit Boards: Nema Grade FR4,
Double Clad with Copper, Plated with Gold
over Nickel
Infrared Light Emitting Diode Chips:
Gallium Aluminum Arsenide
Silicon Phototransistor Chips: Gold and
Aluminum Alloys
Resistor: Metal Oxide on Ceramic Substrate
Solder Pins: Brass, Plated with Tin
Code Rotor: Acetal (Delrin 100)
Code Housing: Polyamide Polymer (Nylon
6/10 Alloy)
Backplate Strain Relief: Hiloy-610
Cable: Copper Standard with Topcoat in
PVC Insulation (Cabled Versions Only)
Connector: PA4.6 with Tin/Lead Plated
Phosphor Bronze (Cable/Connector
Versions)
Label: TT406 Thermal Transfer Cast Film
Solder: 60/40 Tin Lead, No Clean - Low
Residue Flux
Mounting Hex Nut: Cadmium Over 1/2 Hard
Brass
Lockwasher: 8-18 Stainless Steel,
Passivate Finish
Pin Header: Hi-Temp Glass Filled Thermo-
plastic UL94V-0, Phosphor Bronze (Pinned
Versions Only)
Output B
•
•
0
for code change and 24
Magnetic Detent
Original 11292004
Bulletin#1042