54M-1BB-1AL Grayhill Inc, 54M-1BB-1AL Datasheet - Page 53

• Manufacturer Part Number: 54M-1BB-1AL
• Description: 54M30-01-1-03N & 01-1-12N-C T, Military 85&deg
• Manufacturer: Grayhill Inc

Specifications of 54M-1BB-1AL

• , 30°: , 1 Deck, 1 Pole/deck, 2 Positions/pole, Non-shorting & 1 Deck, 1 Pole/deck, 2 Positions/pole, Non-shorting, 54M-1BA-1BA
• Lead Free Status / Rohs Status: Compliant

See page F-63 for specifications, accessories and ordering information.
SERIES 42
1" Diameter, 1 Amp, 10 Max.
Positions/Pole, PC Mount
DIMENSIONS
ADJUSTABLE STOP SWITCHES: Series 42 and 44
F-53
CIRCUIT DIAGRAM: PC Mount
The standard and UL recognized switches are
also available with adjustable stops. Two
removable stop washers allow you to limit the
number of switch positions as needed. A knurled
nut is supplied to secure the washers if desired.
These switches have no bushing keyway. All
other dimensions, ratings and characteristics
are the same as the standard fixed stop styles.
Although not military qualified, the adjustable
styles are useful in military equipment
prototypes. However, when submitting the
equipment for government approval, the fixed
stop qualified style should be substituted.
Termination
One-sided termination is standard for switches with 2 to 5
positions per pole. Two-sided termination is standard for
switches with 6 thru 10 positions per pole.
6 thru 10 positions
per
terminals from one
side of switch are
available on special
order. See Special
Options, page F-10
or contact Grayhill.
Standard Style
Grayhill part number and date code marked on detent cover label. Customer part
number marked on request. UL recognized marking as required.
.219
± .005
(5,56
± 0,13)
Switch is Viewed From Shaft End
Note: All common terminals are located above
pole
and Shown in Position No. 1
C L
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
OF BUSHING
KEYWAY
and
base terminals as shown.
TERMINAL DIMENSIONS AT THIS
POINT ARE .050 ± .005 (1,27 ± 0,13)
WIDE BY .020 ± .003 (0,51 ± 0,08) THICK
(25,4 ± 0,25)
1.000 ± .010
In inches (and millimeters)
8
DIA.
9
7
ONE POLE
10
6
Multi-Deck Rotary Switches
1
5
2
4
3
(19,05 ± 0,25)
C L OF
.750 ± .010
.375 ± .015
(9,53 ± 0,38) TYP.
C1
BUSHING
KEYWAY
TYP.
(15,24 ± 0,79)
(11,10 ± 0,51)
(6,35 ± 0,51)
.600 ± .031
.437 ± .020
.250 ± .020
FEATURES
• Satisfies High Current Board Level
• 36° Angle of Throw Permits up to
• UL Recognized Versions
PC BOARD MOUNTING PATTERN
See additional adjustable stop switch
information at the beginning of the Rotary
Switch section. For ordering information, see
page F-60.
.250 + .001 –.002
(6,35 + 0,03 –0,05)
DIA.
Applications
Ten Positions
(19,05)
.750
TYP.
(9,53)
.375
TYP.
Series 42
C L
.174 (4,42)
OF FRONT SUPPORT
PLATE MOUNTING
HOLES
(12,7)
.500
TYP.
(12,50)
Shown for a two deck switch
.492
(6,35)
60525-5997 • USA • Phone: [phone] • Fax: [phone] • www.grayhill.com
.250
TYP.
TYP.
Front Views
.174
± .010
(4,42
± 0,25)
DIM. A + .046 –.000
(+1,17 –0,00)
BUSHING KEYWAY
.066 ± .002 (1,68 ± 0,05) WIDE BY
.036 ± .003 (0,91 ± 0,08) DEEP
FROM A .375 (9,53) DIA.
3/8-32 UNEF-2A THREAD
(MTG. HOLE=3/8 DIA. MIN.)
INTEGRAL ASSEMBLY NUT,
DO NOT REMOVE
C
L C L C L
.174 (4,42) TYP.
Series 44
COMMON LUG
C
C L OF REAR
C L OF BASE
L
.110 (2,79)
TERMINAL
MOUNTING
HOLES
SUPPORT
PLATE
MOUNTING
HOLES
COMMON
TERMINAL
MOUNTING
HOLES
.830
± .010
(21,08
± 0,25)
.174 ± .010
(4,42 ± 0,25)
#1 THREAD
DIM. B REF.
STUD
PROJECTION
SHAFT AND PANEL SEAL: Srs. 42 & 44
Equivalent Styles
For style 42A36, use 42D36
For style 44A30, use 44D30
For style 42M36, use 42D36 initially
For style 44M30, use 44D30 initially
For style 42U36, use 42UD36
For style 44U30, use 44UD30
The Series 42/44 Styles, which include the letter "S" with the
exception of style "HS", are watertight sealed to the mounting
panel by utilizing the panel seal kit. These switches are built
with a front plate that does not have a non-turn tab. The
panel seal kit consists of a grooved hex nut, a keyed washer
and a keyed panel seal. The grooved hex nut is assembled
to the switch bushing. The keyed washer is slid down the
bushing slot and seated into the hex nut groove. The seal
is likewise assembled to the bushing and hex nut. The
keyed washer is required to provide seal integrity in the
bushing slot. When assembled to the panel, the grooved
nut, backing washer and seal require the same space as a
normal mounting nut. Hence, the seal kit does not alter the
dimensions. Panel seal kit includes a non-turn washer to be
used into a blind hole in the back panel. For panel seal kit
part dimensions, see Accessories. Style "HS" switches use
a similar sealing method, except the integral assembly nut
retains the panel seal. All sealed style switches are provided
with a shaft to bushing internal seal.
Standard Style
USE OF KNURLED
NUT IS OPTIONAL
(37,34 ± 0,51)
1.470 ± .020
TYP.
.786 ± .010
(19,96 ± 0,25)
DIA.
ADJUSTABLE STOP
WASHERS
(12,7 ± 0,38)
.500 ± .015
.187 ± .015
(4,75 ± 0,38) TYP.
.250 ± .015
(6,35 ± 0,38) TYP.
.735 ± .010
(18,67 ± 0,25) TYP.
TYP.