82-101-74 Grayhill Inc, 82-101-74 Datasheet - Page 4

SWITCH, KEYPAD, 1X1, 100mA, 5V, PLASTIC

82-101-74

Manufacturer Part Number
82-101-74
Description
SWITCH, KEYPAD, 1X1, 100mA, 5V, PLASTIC
Manufacturer
Grayhill Inc
Datasheet

Specifications of 82-101-74

Keypad Array
1 X 1
Contact Voltage Dc Nom
5V
Contact Current Max
100mA
Panel Cutout Width
17.35mm
Panel Cutout Height
17.35mm
Housing Material
Plastic
Color
Grey
No. Of Keys
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ORIENTATION OF MODULES
A module, depending on circuitry, may not be
symmetrical. Rotating it 180° will result in a
different pin location. Please note the button
PRINTED CIRCUIT BOARD LAYOUT
Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois
CIRCUIT DIAGRAMS
This layout provides the horizontal printed circuit board layout as viewed from the top side of the
PC board. Turning end to end will result in a different pin location. However, the dimensional
relationship will remain the same.
Lightable Modules–per drawing below.
This drawing indicates the layout to be used for a 6 button module with light sources mounted two
ways: the lamps for the upper 3 buttons are mounted from the top or component side of the board,
and the lamps for the lower 3 buttons are mounted by the easy replacement method. (See also Light
Source and Lamp Mounting.) Light sources, when mounted from the top side of the board, must
be mounted before the keyboard modules; when mounted, lamp should extend no more than .250"
(6,35 mm) above the board.
(12,40 ± 0,08)
The bottom view of the line drawings shows
number (A1, A2, etc.) next to the pin locations
of each switch section. These pin numbers are
directly related to the circuit diagrams. For
example, if the switch under Button A of a
standard module were SPST, the pins would
be located at the "#2" Position. If the module
were a lightable one with SPST circuitry, the
pins would be located at the "#1" Position. If
other locations are desired, specify them.
The coded circuits shown are suggested
possibilities and each button may carry a
different circuit. Location of active pins on
each button may be varied to conform with
layout of the printed circuit board. Up to a 7-bit
code is possible under each button.
Combinations of simple circuitries are also
possible as shown in the sample diagrams.
(2,29)
(12,7 ± 0,76)
.090
TYP.
.500 ± .003
.
488 ± .003
± 0,25)
± .010
(2,39
.094
TYP.
Unlighted Module
(17,45 ± 0,08)
.687 ± .003
C
L
(17,45 ± 0,08)
.687 ± .003
.244 (6,20) TYP.
C
L
identification, the pin location for the desired
circuitry, and the direction of mounting. It is
important to use this information when designing
a printed circuit board layout and when
60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
2
C
C
L
HOLE TO
ACCOMMODATE
.032 (0,81) DIA.
PIN
(17,45 ± 0,08)
SPST
.687 ± .003
.045 ± .002
(1,14 ± 0,05)
TYP.
(8 PLACES)
Note: Coded switches are constructed so that common (C) is made after all other contacts.
2
2
3
C
Standard Modules
.112
± .003
(28,45
± 0,08)
TYP.
2PST
.270 ± .003
(6,86 ± 0,08)
Other Possible Circuit Configurations
C L
Coded Circuitry–To 7 Bits/Button
2
3
DIMENSIONS ARE DEPENDENT ON
LAMP SOURCE. APPROXIMATELY
.020 (0,51) AND .100 (2,54) APART
FOR A T-1 LAMP OR LED
1
2
3
4
C
C
C L
3PST
(17,45 ± 0,08)
.687 ± .003
Modular Keyboards
1
2
3
4
Lightable Module
1
2
3
4
communicating with Grayhill. See Ordering
Information–Special Keyboard Modules on the
next page.
C
C
C L
4PST
(17,45 ± 0,08)
.687 ± .003
1
2
3
4
1
C
C
C
L
Lightable Modules
SPST
1
HOLE TO
ACCOMMODATE
.032 (0,81) DIA.
PIN
.170 (4,32)
RECOMMENDED
DIA. HOLE
ACCOMMODATES
LAMP IN EASY
REPLACEMENT
MOUNTING
1
4
C
C
2PST
1
4
Keypads
43

Related parts for 82-101-74