SI-HG63-TK1 BANNER ENGINEERING, SI-HG63-TK1 Datasheet - Page 2

• Manufacturer Part Number: SI-HG63-TK1
• Description: Replacement Accessory Kit
• Manufacturer: BANNER ENGINEERING

Specifications of SI-HG63-TK1

• Accessory Type: Replacement Accessory Kit
• For Use With: Safety Interlock Switches, SI-HG63 Series

Hinge Switches –

In the United States, the functions that Banner safety switches are intended to perform are regulated by the Occupational Safety and
Health Administration (OSHA). Whether or not any particular safety switch installation meets all applicable OSHA requirements depends
upon factors that are beyond the control of Banner Engineering Corp. These factors include the details of how the safety switches are
applied, installed, wired, operated, and maintained.
Banner Engineering Corp. has attempted to provide complete application, installation, operation, and maintenance instructions. This
information is found in the instruction manual packaged with each safety switch. In addition, we suggest that any questions regarding
the use or installation of safety switches be directed to the factory applications department at the telephone numbers or address shown
below.
Banner Engineering Corp. recommends that safety switches be applied according to the guidelines set forth in international (ISO/IEC)
standards listed below. Specifically, Banner Engineering Corp. recommends application of these safety switches in a configuration which
meets safety category 4, per ISO 13849-1 (EN954-1).
In addition, the user of Banner safety switches has the responsibility to ensure that all local, state, and national laws, rules, codes, and
regulations relating to the use of Banner safety switches in any particular application are satisfied. Extreme care is urged that all legal
requirements have been met and that all installations and maintenance instructions are followed.
U.S. Regulations Applicable to Use of Banner Safety Switches
U.S. Standards Applicable to Use of Banner Safety Switches
Applicable European and International Standards
OSHA Code of Federal Regulations: Title 29, Parts 1900 to 1910
ANSI B11
ISO 12100-1/-2
(EN 292-1/-2)
ISO 13852 (EN 294)
ISO 13853 (EN 811)
ISO 13849-1 (EN 954-1) “Safety of Machinery—Safety Related Parts of Control Systems”
ISO 13855 (EN 999)
ISO 14119 (EN 1088)
IEC/EN 60204-1
IEC/EN 60947-5-1
P/N 129465
Important Information
“Safety of Machinery—Basic Concepts, General Principles for Design”
“Safety of Machinery—Safety Distances to Prevent Danger Zones Being Reached by the Upper Limbs”
“Safety of Machinery—Safety Distances to Prevent Danger Zones Being Reached by the Lower Limbs”
“ Safety of Machinery—The Positioning of Protective Equipment in Respect to Approach Speeds of Parts of
“Safety of Machinery—Interlocking Devices Associated with Guards—Principles for Design and Selection”
“Safety of Machinery—Electrical Equipment of Machines”
“Low Voltage Switchgear—Electromechanical Control Circuit Devices”
Available from:
the Human Body”
Available from:
“ Standards for Construction, Care, and Use of Machine Tools”
Available from:
SI-HG63 Series
Toll Free:
Email:
Address:
Superintendent of Documents
Government Printing Office
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: [phone]
Safety Director
AMT—The Association for Manufacturing Technology
7901 Westpark Drive
McLean, VA 22102
Tel: [phone]
Global Engineering Documents
15 Inverness Way East
Englewood, CO 80112-5704
Phone: [phone]
Fax: [phone]
1-888-3-SENSOR (1-888-373-6767)
[e-mail]
9714 Tenth Avenue North
Minneapolis, MN 55441
Application Assistance
Regarding the Use of Safety Switches
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]