MCP4431-104E/ML Microchip Technology, MCP4431-104E/ML Datasheet - Page 7

• Manufacturer Part Number: MCP4431-104E/ML
• Description: IC POT 100K QUAD 7BIT 20QFN
• Manufacturer: Microchip Technology

Specifications of MCP4431-104E/ML

• Package / Case: 20-VFQFN Exposed Pad
• Resistance (ohms): 100K
• Taps: 129
• Number Of Circuits: 4
• Temperature Coefficient: *
• Memory Type: Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Number Of Pots: Quad
• Taps Per Pot: 129
• Resistance: 100 KOhms
• Wiper Memory: Volatile
• Digital Interface: I2C
• Operating Supply Voltage: 1.8 V to 5.5 V
• Supply Current: 600 uA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Serial Interfaces
Microchip currently offers devices with one of the following
three serial interfaces:
■
■
■
Increment
Decrement
Digital Potentiometer Solutions
Devices with Up/Down Interface
1. Resistor options are: -202 (2.1 kΩ), -502 (5.0 kΩ), -103 (10.0 kΩ), and -503 (50.0 kΩ).
2. Resistor options are: -502 (5.0 kΩ), -103 (10.0 kΩ), 503 (50.0 kΩ), and -104 (100.0 kΩ).
3. Zero-scale allows the wiper to “directly” connect to Terminal B, while full-scale allows the wiper to “directly” connect to Terminal A.
4. There is one R
5. This current is with the serial interface inactive, and not during an EEPROM write cycle (for non-volatile devices).
6. The serial interface has been tested to 1.8V, the device’s analog characteristics (resistor) have been tested from 2.7V to 5.5V. Review the device’s characterization graphs for information on analog performance between
7. One of the terminal pins (A or B) is internally connected to ground, due to the limitation of the number of pins on the package.
8. Shutdown support via software (TCON register(s)). If device has SHDN pin, software shutdown also fuctions.
9. High voltage command support is for compatibility with the corresponding non-volatile version of the device.
Device
MCP4011
MCP4012
MCP4013
MCP4014
MCP4021
MCP4022
MCP4023
MCP4024
1.8V and 2.7V.
An Up/Down interface
An SPI interface
An I
2
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
C interface
S
resistor between the maximum wiper value and Terminal A.
U/D
U/D
U/D
U/D
U/D
U/D
U/D
U/D
Vol
Vol
Vol
Vol
NV
NV
NV
NV
63
63
63
63
63
63
63
63
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
33.3/79.4/158.7/793.7
Y/Y
Y/Y
Y/Y
Y/Y
Y/Y
Y/Y
Y/Y
Y/Y
1
1
1
1
1
1
1
1
N
N
N
N
Y
Y
Y
Y
Up/Down Interface
This is an easy to implement interface that requires two pins
and can be implemented with minimal software overhead.
This interface is also easy for test systems when using
the non-volatile devices as replacements for mechanical
potentiometers.
High voltage commands require the CS pin forced to the
V
WiperLock Technology bit can be enabled and disabled.
IHH
Y
Y
Y
Y
Y
Y
Y
Y
(9)
(9)
(9)
(9)
voltage, instead of the V
Digital Potentiometer Design Guide
N
N
N
N
N
N
N
N
Rheo
Rheo
Rheo
Pot
Rheo
Pot
Pot
Pot
(7)
(7)
(7)
(7)
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
1.8V to 5.5V
2.7V to 5.5V
2.7V to 5.5V
2.7V to 5.5V
2.7V to 5.5V
IL
(6)
(6)
(6)
(6)
voltage. In this state, the
8
6
6
5
8
6
6
5
DFN 2x3
SOT
SOT
SOT
SC70
SC70
SC70
SC70
7
1
1
1
1
1
1
1
1