PTGL13AR1R0M1C04B0 Murata Electronics North America, PTGL13AR1R0M1C04B0 Datasheet - Page 70
![no-image](/images/manufacturer_photos/0/4/466/murata_electronics_north_america_sml.jpg)
PTGL13AR1R0M1C04B0
Manufacturer Part Number
PTGL13AR1R0M1C04B0
Description
THERMISTOR
Manufacturer
Murata Electronics North America
Datasheet
1.PRF21AR471QB5RA.pdf
(84 pages)
Specifications of PTGL13AR1R0M1C04B0
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
Above mentioned soldering in "2. Adhesive Strength" and "3. Vibration" is done following condition at our side.
1
2
3
4
5
6
7
8
Specifications and Test Methods
(*1) Measurement resistance after the test by applying voltage of less than 1.5Vdc by a direct current of less than 10mA after product is left at 25±2°C for 2 hours.
(*2) Sensing temp. change: not to exceed ±1°C
#Glass-Epoxy PC board
#Standard land dimension
#Standard solder paste
#Standard solder profile
Above conditions are mentioned in Notice.
Resistance Value (at 25°C)
Adhesive Strength
Vibration
Solderability
Solder-heatability
Temperature Cycling
Humidity Test
High Temperature
Load Test
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
The resistance value should be within the specified
tolerance.
There is no sign of electrode exfoliation
Normal appearance
Resistance change: not to exceed ±20% (*1)
Min. 75% electrode is covered with new solder.
Resistance change: not to exceed ±20% (*1)
Normal appearance
Resistance change: not to exceed ±20% (*1)
Normal appearance
Resistance change: not to exceed ±20% (*1, 2)
Normal appearance
Resistance change: not to exceed ±20% (*1, 2)
Normal appearance
Resistance change: not to exceed ±20% (*1, 2)
Chip Tight Tolerance Type Specifications and Test Methods
Rating Value
After applying maximum operating voltage for 3 minutes and
leaving for 2 hours at 25°C, measured by applying voltage of
less than 1.5Vdc. (by a direct current of less than 10mA).
EIAJ ET-7403 term 9
Solder PTC to PCB and add a force of 5.0N in the direction
shown below.
JIS C 5102 term 8.2
Soldered PTC to PCB
JIS C 5102 term 8.4
JIS C 5102 term 9.3
Times: 5 cycles
JIS C 5102 term 9.5
40±2°C, 90-95%RH leave for 500±8 hours.
JIS C 5102 term 9.10
85±5°C (in air), load maximum operating voltage for 1000±12
hours.
Vibration: 10-55-10Hz (1 min.)
Width: 1.5mm
Vibrate for 2 hours in each of 3 mutually perpendicular
planes for a total of 6 hours.
Solder: Sn 63%/Pb 37% (or 60/40%)
Solder temp: 230±5°C
Soaking time: 3±0.5 seconds.
Soaking position: Until a whole electrode is soaked
Solder: Sn 63%/Pb 37% (or 60/40%)
Flux: Solder paste containing less than 0.2wt% of chlorine.
Preheating: 150±5°C 3 minutes.
Peak temp.: 260±5°C 10±5 seconds. (reflow)
PCB: Glass Epoxy PCB (JIS C 6484)
Step
1
2
3
4
Room temp.
Room temp.
+150 +3, -0
Temp. (°C)
-20 +0, -3
Method of Examination
PTC
F
Time (minute)
10-15
10-15
30
30
Glass Epoxy PCB
F=5.0N
F
R90E.pdf
69
07.3.19
10