A3251EUA Allegro Microsystems Inc, A3251EUA Datasheet
A3251EUA
Specifications of A3251EUA
Related parts for A3251EUA
A3251EUA Summary of contents
Page 1
These parts are in production but have been determined to be NOT FOR NEW DESIGN. This classification indicates that sale of this device is currently restricted to existing customer applications. The device should not be purchased for new design applications ...
Page 2
Features and Benefits ▪ Chopper stabilization for stable switchpoints throughout operating temperature range ▪ Externally programmable operate point (through VCC pin) ▪ On-board voltage regulator for 4 operation ▪ On-chip protection against: ▫ Supply transients ▫ ...
Page 3
A3250 and A3251 Description (continued) The other differences in the devices are the power-on state. The A3250 powers-on in the HIGH state, while the A3251 powers-on in the LOW state. Three package styles provide a magnetically optimized package Selection Guide ...
Page 4
A3250 and A3251 OPERATING CHARACTERISTICS valid over operating T Characteristic Symbol ELECTRICAL CHARACTERISTICS Supply Voltage 1 Output Saturation Voltage V Output Leakage Current Supply Current Output Rise Time Output Fall Time Chopping Frequency Power-Up Time Output Current Limit 1,2 I ...
Page 5
A3250 and A3251 All data are taken with A3250 devices, the average of 3 lots, 30 pieces per lot Average B vs Program Code -50 - ...
Page 6
A3250 and A3251 All data are taken with A3250 devices, the average of 3 lots, 30 pieces per lot Average B vs. Temperature hys Program Code -50 - ...
Page 7
A3250 and A3251 All data are taken with A3250 devices, the average of 3 lots, 30 pieces per lot Average I vs. Temperature CC(on -50 - (°C) A 280 260 240 ...
Page 8
A3250 and A3251 THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic Package Thermal Resistance Power Derating Curve 1-layer PCB, Package 180 ºC/W) θJA ...
Page 9
A3250 and A3251 Chopper-Stabilized Technique The Hall circuit is based on a Hall element, a small sheet of semiconductor material in which a constant bias current flows when a constant voltage source is applied. The output takes the form of ...
Page 10
A3250 and A3251 Programming Protocol The operate switchpoint can be field-programmed so, a coded series of voltage pulses through the VCC pin is used to set bitfields in onboard registers. The effect on the device ...
Page 11
A3250 and A3251 The pulse sequences consist of the following groups of pulses enable sequence bitfield address sequence. 3. When permanently setting the bitfield, a long V ing pulse. (Note: Blown bit fuses cannot be reset.) ...
Page 12
A3250 and A3251 The first segment of code is a Enabling Addressing Mode. keying sequence used to enable the bitfield addressing mode. As shown in figure 4, this segment consists of one short V seven or more V pulses, and ...
Page 13
A3250 and A3251 For additional general application information, visit the Allegro MicroSystems Web site at www. allegromicro.com. Typical Application Circuit It is strongly recommended that an external ceramic bypass capacitor the range of 0.01 μF to 0.1 ...
Page 14
A3250 and A3251 Power Derating The device must be operated below the maximum junction temperature of the device Under certain combinations of J(max) peak conditions, reliable operation may require derating sup- plied power or improving the heat dissipation ...
Page 15
A3250 and A3251 +0.15 2.45 +0.15 –0.16 4.10 –0.16 1 0.42±0.06 0.50±0.06 For Reference Only; not for tooling use (reference JEDEC. TO-243AA) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration ...
Page 16
A3250 and A3251 4.09 45° +0.08 3.02 –0.05 2.16 MAX 0.51 REF 1 2 15.75 ±0.51 +0.05 0.43 –0.07 Copyright ©2004-2010, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such de par tures ...