AS5043-ASSU austriamicrosystems, AS5043-ASSU Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/0/84/austriamicrosystems_sml.jpg)
AS5043-ASSU
Manufacturer Part Number
AS5043-ASSU
Description
IC ENCODER PROG 10-BIT 16-SSOP
Manufacturer
austriamicrosystems
Type
Linear, Rotary Encoder - Programmabler
Datasheet
1.AS5043_PB.pdf
(36 pages)
Specifications of AS5043-ASSU
Sensing Range
45mT ~ 75mT
Voltage - Supply
3 V ~ 3.6 V, 4.5 V ~ 5.5 V
Current - Supply
21mA
Current - Output (max)
4mA
Output Type
Analog, Digital
Features
Programmable
Operating Temperature
-40°C ~ 125°C
Package / Case
16-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AS5043-ASSU
Manufacturer:
AMS
Quantity:
101
AS5043
Data Sheet – Programming the AS5043
Figure 14: Analog Output Block Diagram
12.2.1 Angular Range Selector
The Angular Range selector allows a digital pre-selection of the angular range. The AS5043 can be configured for a full
scale angular range of 45°, 90°, 180° or 360°. In addition, the Output voltage versus angle response can be fine-tuned by
setting the gain of the OP-AMP with external resistors and the maximum output voltage can be set in the DAC.
The combination of these options allows to configure the operation range of the AS5043 for all angles up to 360° and
output voltages up to 5.5V.
The response curve for the analog output is linear for the selected range (45°/90°/180°/360°). In addition, the slope is
mirrored at 180° for 45°- and 90°- modes and has a step response at 270° for the 180°-mode. This allows the AS5043 to
be used in a variety of applications. In these three modes, the output remains at V
output change when the mechanical angle is rotated beyond the selected analog range. In 360°-mode, a jitter between
V
www.austriamicrosystems.com
out,max
from
DSP
Magnetic field range alarm. Active
low. Leave open or connect to
VSS if not used
AS5043
Digital serial
interface, 10bit/360°.
Leave open if not
used. CSn and CLK
may also be tied to
VSS if not used
CSn
and V
OR1
3
CLK
0 360° 0
0 180° 1
1 90° 0
1 45° 1
Selector
Range
out,min
OR0
4
DO
MagRngn
6
at the 360° point is also prevented due to a hysteresis.
1
PROG
digital
10bit
8
for OTP
programming and
alignment mode
only. Leave open
or connect to VSS
if not used
0= 0-100% * Vref (def.)
1= 10-90% * Vref
ClampMdEN
DAC
Mode pin.
Default = open
(low noise)
Vref
Mode
2
0 - 100% VDD5V /2
NC
REF_extEN
5
Test pins.
Leave open
External DAC reference pin.
Leave open or connect to
VSS if not used
0=int
1=ext
NC
13
DACref
NC
14
Revision 1.80
9
analog
VDD5V / 2
10bit
VDD
FB_intEN
VDD5V
Vout
Gain = 2x (int)
0
+
-
16
LDO
3.3V
0=ext
1=int
VSS
VDD3V3
out,max
DACout
7
Rf_int
30k
Rg_int
30k
VOUT
FB
and V
OP-Amp feedback pin.
Leave open if not used.
15
DAC output pin.
Leave open if not used
10
12
11
Rf
out,min
+
Connect pins 15 and
16 for VDD= 3.0-3.6V.
Do NOT connect for
VDD = 4.5-5.5V !
1-10µF
Rg
360°angle
RLmin
= 4k7
to avoid a sudden
2
Vout
1
C
<100pF
3
L
15 – 36
VDD
VSS