HMC5843-TR Honeywell Microelectronics & Precision Sensors, HMC5843-TR Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/308/honeywell_microelectronics___precision_sensors_sml.jpg)
HMC5843-TR
Manufacturer Part Number
HMC5843-TR
Description
SENSOR MAGNETIC 3 AXIS 20-LCC
Manufacturer
Honeywell Microelectronics & Precision Sensors
Series
HMCr
Type
Compass - Three Axisr
Datasheet
1.HMC5843-TR.pdf
(20 pages)
Specifications of HMC5843-TR
Sensing Range
±4g
Voltage - Supply
2.5 V ~ 3.3 V
Current - Supply
80µA
Output Type
Differential Voltage
Features
Compass - Three Axis
Operating Temperature
-30°C ~ 80°C
Package / Case
20-LCC
Pin Count
20
Screening Level
Commercial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output (max)
-
Lead Free Status / Rohs Status
Supplier Unconfirmed
Other names
342-1071-2
HMC5843
HMC5843
HMC5843
MODES OF OPERATION
This device has several operating modes whose primary purpose is power management. This section describes these
modes.
Continuous-Measurement Mode
During continuous-measurement mode, the device continuously makes measurements and places measured data in data
output registers.
Settings in the configuration register affect the data output rate (bits DO[n]), the measurement
configuration (bits MS[n]), and the gain (bits GN[n]) when in continuous-measurement mode. To conserve current
between measurements, the device is placed in a state similar to idle mode, but the mode is not changed to idle mode.
That is, MD[n] bits are unchanged.
Data can be re-read from the data output registers if necessary; however, if the
master does not ensure that the data register is accessed before the completion of the next measurement, the new
2
measurement may be lost. All registers maintain values while in continuous-measurement mode. The I
C bus is enabled
for use by other devices on the network in while continuous-measurement mode.
Single-Measurement Mode
This is the default single supply power-up mode. In dual supply configuration this is the default mode when AVDD goes
high. During single-measurement mode, the device makes a single measurement and places the measured data in data
output registers. Settings in the configuration register affect the measurement configuration (bits MS[n]), and the gain
(bits GN[n]) when in single-measurement mode. After the measurement is complete and output data registers are
updated, the device is placed sleep mode, and the mode register is changed to sleep mode by setting MD[n] bits. All
2
registers maintain values while in single-measurement mode. The I
C bus is enabled for use by other devices on the
network while in single-measurement mode.
Idle Mode
2
During this mode the device is accessible through the I
C bus, but major sources of power consumption are disabled,
such as, but not limited to, the ADC, the amplifier, the SVDD pin, and the sensor bias current. All registers maintain
2
values while in idle mode. The I
C bus is enabled for use by other devices on the network while in idle mode.
Sleep Mode
This is the default dual supply power-up mode when only DVDD goes high and AVDD remains low. During sleep mode
2
the device functionality is limited to listening to the I
C bus. The internal clock is not running and register values are not
maintained while in sleep mode. The only functionality that exists during this mode is the device is able to recognize and
2
execute any instructions specific to this device but does not change from sleep mode due to other traffic on the I
C bus.
2
The I
C bus is enabled for use by other devices on the network while in sleep mode. This mode has two practical
differences from idle mode. First this state will create less noise on system since the clock is disabled, and secondly this
state is a lower current consuming state since the clock is disabled.
Off Mode
2
During off mode device is off. No device functionality exists. Both AVDD and DVDD are low. The I
C bus is enabled for
2
use by other devices on the network in off mode. In this mode the I
C pins shall be in a high impedance state.
10
www.honeywell.com