A1383EUA-T Allegro Microsystems Inc, A1383EUA-T Datasheet - Page 15

• Manufacturer Part Number: A1383EUA-T
• Description: IC SENSOR HALL EFFECT PREC 3-SIP
• Manufacturer: Allegro Microsystems Inc
• Series: A138xr
• Type: Linear - Programmabler

Specifications of A1383EUA-T

• Sensing Range: 2.75mV/G ~ 4.25mV/G
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 8mA
• Current - Output (max): 10mA
• Output Type: Analog, Ratiometric
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 3-SIP
• Peak Reflow Compatible (260 C): Yes
• Accuracy %: 1.5%
• Supply Voltage: 5V
• Output Current: 2mA
• Termination Type: SIP
• Bandwidth: 21kHz
• Supply Voltage Max: 5.5V
• Sensitivity: 2.75 To 4.25 MV/G
• No. Of Pins: 3
• Hall Effect Type: Linear
• Supply Voltage Min: 4.5V
• Operating Temperature Max: 85°C
• Rohs Compliant: Yes
• Filter Terminals: SIP
• Leaded Process Compatible: Yes
• Operating Temperature Min: -40°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

A1381, A1382,
A1383, and A1384
Initial State
reset to a known state. This is referred to as the Initial state. All
the bit field locations that have intact fuses are set to logic 0.
While in the Initial state, any V
ignored. To enter the Parameter Selection state, apply one V
pulse on the VOUT pin.
Parameter Selection State
parameter register containing the bit fields to be programmed. To
select a parameter register, increment through the keys by apply-
ing V
following programming parameters:
•
•
•
To enter the Bit Field Addressing state, apply one V
the VOUT pin.
1 pulse - Sens
2 pulses - V
3 pulses - TC
PM
pulses on the VOUT pin. Register keys select among the
After system power-up, the programming logic is
OUT(Q)
V
V
PM
PH
SENS
= V
= V
, POL, and LOCK
P(LOW)
P(LOW)
–V
–V
This state allows the selection of the
P(HIGH)
P(MID)
PM
–V
pulses on the VOUT pin are
–V
Programmable Linear Hall Effect Sensor ICs with Analog Output
V
V
P(LOW)
PM
PM
P(LOW)
Available in a Miniature Thin Profile Surface Mount Package
SENS
1
Programming State Machine
V
V
PM
PM
PH
pulse on
Bit Field Addressing
User Power-Down
Parameter Selection
PH
Fuse Blowing
V
Power-Up
Required
PH
V
Initial
OUT(Q)
2
V
V
PH
PH
Bit Field Addressing State
individual bit fields to be programmed in the selected parameter
register (see Programming Logic table). To leave this state, either
cycle device power or blow the fuses for the selected code. Note
that merely addressing the bit field does not permanently set
the value of the selected programming parameter; fuses must be
blown to do so.
Fuse Blowing State
V
cycled before additional programming is attempted. Note: Each
bit representing a decimal code must be blown individually (see
the Fuse Blowing section).
PH
V
V
PM
PM
pulse on the VOUT pin. Power to the device should then be
V
PM
V
TC
2
n = total
register
PH
LOCK
POL,
bits in
n
SENS
– 1
To blow an addressed bit field, apply a
,
V
V
PM
PM
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 [phone]
www.allegromicro.com
This state allows the selection of the
15