E34PB3 EATON CUTLER HAMMER, E34PB3 Datasheet - Page 319
![no-image](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_sml.jpg)
E34PB3
Manufacturer Part Number
E34PB3
Description
Pushbutton Switch Operator
Manufacturer
EATON CUTLER HAMMER
Datasheet
1.10250T102.pdf
(320 pages)
Specifications of E34PB3
Circuitry
SPST-NO
Actuator Diameter
30mm
Switch Operation
(ON)
Contact Current Max
10A
Switch Terminals
Plug-In
Illumination
Non Illuminated
For Use With
E34 Series Pushbutton Switches
- Current page: 319 of 320
- Download datasheet (7Mb)
Ratings
Summary of NEC Article 500
The NEC Article 500 explains
in great detail the
requirements for the
installation of wiring and
electrical equipment in
hazardous locations. The
purpose of this summary is
for general reference only,
the National Electric Code
along with other applicable
authorities having jurisdiction
over the site should be the
installer’s guidelines when
wiring or installing electrical
equipment in any hazardous
or potentially hazardous
location.
Class I, Division 2 Definition
Class I, Division 2 covers
hazardous locations where
flammable gases, vapors or
volatile liquids are handled
either in a closed system, or
confined within suitable
enclosures, or where
hazardous concentrations are
normally prevented by
positive mechanical
ventilation. Areas adjacent to
Division 1 locations, into
which gases might
occasionally flow, would
also belong to Division 2
(NEC (500-5[b])).
Hazardous Location
Any area where there is the
possibility of explosion and
fire resulting from the
presence of flammable
vapors, liquids or gas, or
combustible dust or fibers.
Summary of NEC Article 505
The NEC also classifies
hazardous locations for
flammable gases and vapors
into zones under NEC 505.
This system is more in line
with the European
Standards, CENELEC and
IEC, with the major
difference being that NEC
505 only classifies gases and
vapors while CENELEC and
IEC also include dusts.
Summary of Classifications
NEC 500–503
Class
NEC 505
Class
Note
For additional information on grouping of compounds, see NFPA 497M-1991 and NFPA 325-1994.
I. Gas
II. Dust
III. Fibers
I. Gas
30.5 mm Class I Division 2 Hazardous Locations—10250T/E34
Division
Zone
1. Hazard may exist—May exist in
2. Potential hazard—May be present in
1. Hazard may exist—May exist in
2. Potential hazard—May be present in
1. Production areas
2. Handling and storage areas
0. Continuously present or present for long
1. Likely to exist under normal operating or
2. Not likely to occur in normal operation
atmosphere under normal operating
conditions
atmosphere only under abnormal
circumstances OR location adjacent to
Class I, Division 1 location
atmosphere under normal operating
conditions
atmosphere only under abnormal
circumstances
periods of time
maintenance conditions or adjacent to
Zone 0
and if they do occur will only exist for
short period or adjacent to Zone 1
Pushbuttons and Indicating Lights
Control Products Catalog CA08102001E—August 2010 www.eaton.com
Group
Group
A. Acetylene
B. Hydrogen and manufactured gases containing 30% hydrogen by
C. Petrochemicals (e.g. carbon monoxide, ether, ethylene, hydrogen
D. Petrochemicals (e.g. gasoline, benzene, butane, propane, acetone,
A. Acetylene
B. Hydrogen and manufactured gases containing 30% hydrogen by
C. Petrochemicals (e.g. carbon monoxide, ether, ethylene, hydrogen
D. Petrochemicals (e.g. gasoline, benzene, butane, propane, acetone,
E. Conductive and combustible dust (resistivity <10
F. Carbonaceous dusts (resistivity >10
G. Non-conductive combustible dust (resistivity ≥10
F. Carbonaceous dusts (resistivity >10
G. Non-conductive combustible dust (resistivity ≥10
Easily ignitable fibers or flyings
Easily ignitable fibers or flyings
IIC. Acetylene, hydrogen or equivalent hazard
IIB. Acetaldehyde, ethylene or equivalent hazard
IIA. Acetone, ammonia, ethyl alcohol, gasoline, methane, propane or
IIC. Acetylene, hydrogen or equivalent hazard
IIB. Acetaldehyde, ethylene or equivalent hazard
IIA. Acetone, ammonia, ethyl alcohol, gasoline, methane, propane or
IIC. Acetylene, hydrogen or equivalent hazard
IIB. Acetaldehyde, ethylene or equivalent hazard
IIA. Acetone, ammonia, ethyl alcohol, gasoline, methane, propane or
volume (e.g. butadiene, ethylene oxide, propylene oxide)
sulfide, morpholine, cyclopropane)
ammonia, vinyl chloride)
volume (e.g. butadiene, ethylene oxide, propylene oxide)
sulfide, morpholine, cyclopropane)
ammonia, vinyl chloride)
(metal dusts)
(e.g. carbon black, coke dust, coal)
(e.g. grain dust, flour, starch, sugar, plastics)
(e.g. carbon black, coke dust, coal)
(e.g. grain dust, flour, starch, sugar, plastics)
equivalent hazard
equivalent hazard
equivalent hazard
2
2
ohms/cm but ≤10
ohms/cm but ≤10
47.9
5
5
5
ohm/cm)
ohms/cm)
ohms/cm)
8
8
ohms/cm)
ohms/cm)
319
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
Related parts for E34PB3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ELC-EX08NNDN-2](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
PROGRAMMABLE LOGIC CONTROLLER
Manufacturer:
EATON CUTLER HAMMER
![1251](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Pm Power Pro 3000/5000 A-B Accel/On Interface
Manufacturer:
EATON CUTLER HAMMER
![BHT](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Handle Tie Bar For (2) - 1 Pole Type BR Breakers
Manufacturer:
EATON CUTLER HAMMER
![CH2150](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Type CH Breaker 150A/2 Pole 120/240V 10K
Manufacturer:
EATON CUTLER HAMMER
![CHH3125H4X](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Tenant Branch Breaker 125A/3 Pole 120/240V 42K
Manufacturer:
EATON CUTLER HAMMER
![CL125](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Type CL Breaker 25A/1Pole 120/240V 10K-Classified 1" Ckt Bkr
Manufacturer:
EATON CUTLER HAMMER
![FD1080](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
FD BREAKER 1P 80 AMP WITH LOAD ONLY TERMINALS
Manufacturer:
EATON CUTLER HAMMER
![GD2025](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
GD 2 POLE BREAKER, 25 AMP, SINGLE PACKED
Manufacturer:
EATON CUTLER HAMMER
![BHT](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Handle Tie Bar For (2) - 1 Pole Type BR Breakers
Manufacturer:
EATON CUTLER HAMMER
![CL125](/images/manufacturer_photos/0/2/208/eaton_cutler_hammer_tmb.jpg)
Part Number:
Description:
Type CL Breaker 25A/1Pole 120/240V 10K-Classified 1" Ckt Bkr
Manufacturer:
EATON CUTLER HAMMER