4310A-8-B-2 ARTISAN CONTROLS, 4310A-8-B-2 Datasheet - Page 3

• Manufacturer Part Number: 4310A-8-B-2
• Description: SOLID STATE TIMER SPST-NO 300SEC, 120VAC
• Manufacturer: ARTISAN CONTROLS

Specifications of 4310A-8-B-2

• Contact Configuration: SPST-NO
• Nom Input Voltage: 120VAC
• Delay Time Range: 1s To 300s
• Timing Adjustment: Resistor
• Relay Mounting: Plug In
• Supply Voltage: 115VAC
• Time Range Max: 300s
• Contact Form: SPST-NO
• Current, Rating: 70 mA-5 A
• Dielectric Rating: 1500 V (RMS)
• Function: Timing
• Relay Type: Solid State
• Standards: cULus, UL
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -20 °C
• Termination: Quick Connect
• Timer Type: Single Shot
• Timing Range: 1 to 300 sec.
• Voltage, Control: 120 VAC
• Leaded Process Compatible: Yes
• Load Current Rms Max: 5A
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Notice: Artisan Controls Corporation assumes no responsibility for customers applications or product design. The information and data contained herein is the
sole and exclusive property of Artisan Controls Corporation. Any duplication, misuse, or conversion of this information without the express written consent of
Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property
Output Voltage Drop in “ON” State:
Fixed Timing Purchase Tolerance:
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leakage Current in “OFF” State:
Repeatability Of Timing Period:
Timing Resistor Tolerance:
Data Sheet Revision Date:
Timing Range Tolerance:
Tel: [phone] • Fax: [phone] • Toll Free: 800-457-4950
Operating Temperature:
Zero Voltage Switching:
Timing Resistor Rating:
Artisan Controls Corporation, 111 Canfield Ave., Bldg B15-18, Randolph, NJ, 07869, USA
Transient Protection:
Agency Approvals:
Operating Voltage:
Voltage Tolerance:
Operating Current:
Adjustable Timing:
V
Timing Variation:
I S I T O U R W E B S I T E A T
Output Rating:
Recycle Time:
Solid State Timers and Controllers
Timing Mode:
Fixed Timing:
Construction:
Start Switch:
Dielectric:
Humidity:
12V DC, 24V DC, 48V DC, 24V AC, 48V AC, 115V AC, 230V AC.
±20%, AC 50/60 Hz.
All voltages < 20mA plus load current requirements.
Interval or Single-Shot.
From 0.10 seconds to 8,000 seconds.
±2%, ±5%, ±10%, and ±20%.
0.1 seconds to 8000 seconds covered by 5 ranges. Each range specified is
covered from minimum to maximum using a 0 to 10 Meg ohm external timing
resistance.
Minimum time - 15% +0%, maximum time - 0% +15%. Example: The -3 timing
range operates in the 2 - 100 second range with 0 - 1 meg ohm external timing
resistor could exhibit a minimum time of 1.7 seconds (2 seconds - 15%) with 0
ohms external timing resistance, and a maximum time of 115 seconds (100
seconds + 15%) with an external timing resistor of 1 meg ohm. The extended
range to 1000 seconds using 10 meg ohms external timing resistance could be
as high as 1150 seconds (1000 seconds + 15%).
Worst case power dissipation never exceeds 15 milliwatts.
Timing range specified is guaranteed as a minimum using 5% resistors.
Less than 6% of set point over specified temperature and voltage range.
Operating voltage must be removed for a minimum of 200 milliseconds to
guarantee all timing and output circuits have reset.
SPST-NO closes to initiate an output interval. Switch must be rated for low
level operation down to 500 microamperes at 12V DC. When operating in the
Single-Shot mode (terminals 6 & 7 jumpered) the Initiate switch must be
closed for a minimum of 50mS to assure a full single-shot output timing
interval. The Initiate switch may be reclosed 50mS after the timing interval has
completed and the output switch turned off.
-A & -C models rated for 70mA to 1A inductive with inrush currents to 15 A for 8
mS. -B & -D models rated for 70 mA to 5 A inductive with inrush currents to 40A
for 8 mS. The -B & -D models can be extended to operate as high as 10A
providing the metal base of the timer is maintained at a temperature no greater
than 85°C. This can generally be achieved if ambient temperature does not
exceed 30°C and the timer is mounted to a metal chassis that provides a
minimum of 15 cubic inches of heat sink. Apply a thermal compound between
the timer’s base and the chassis.
-A & -B AC models provide zero voltage switching within 50 microseconds of
zero volts (standard), -C & -D AC models provide random voltage switching.
2 volts maximum for DC models, 3 volts maximum for AC models.
2 mA maximum for DC models, 4 mA maximum for AC models.
Protected by silicon transient suppressors which respond within 1 x 10
seconds to a peak pulse power dissipation of 1500 watts, with surge currents
to 200 amperes for durations up to 1/120 second at 25° C. Maximum transient
voltage protection is 6000 volts as delivered through a source resistance of 30
ohms with a maximum duration of 8.3 milliseconds.
1500V rms all terminals to case on -A & -C models, to heat sink on -B & -D.
-20°C to +85°C.
95% non-condensing.
Encapsulated module with .25 quick connect wiring terminals.
UL File E47858: Component Appliance Controls ATNZ2(US) & ATNZ8(Can),
Component Auxiliary Devices NKCR2(US) & NKCR2(Can).
January 20, 2006
1% nominal.
:
www.artisancontrols.com
-12