S2EB-L2-5V PANASONIC EW, S2EB-L2-5V Datasheet - Page 4

• Manufacturer Part Number: S2EB-L2-5V
• Description: POWER RELAY, DPST-NO/NC, 5VDC, 4A, PCB
• Manufacturer: PANASONIC EW

Specifications of S2EB-L2-5V

• Relay Type: Latching
• Coil Voltage Vdc Nom: 5V
• Contact Current Max: 4A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 130ohm
• Contact Configuration: DPST
• Coil Type: DC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ACCESSORIES
Dimensions
Inserting and removing method
Inserting method: Insert the relay as
shown in Fig. 1 unit the rib of the relay
snaps into the clip of the socket.
Removing method:
(1) Remove the relay straight from the
socket holding the shaded portion of the
relay as shown in Fig. 2.
(2) When sockets are mounted in close
proximity, use a slotted screw driver as
shown in Fig. 3.
NOTES
1. Special use of 2 coil latching types: 2
ways can be considered if 2 coil latching
types are used as 1 coil latching types.
(A) Reverse polarity is applied to the set
coil of 2 coil latching type.
(B) By shorting terminals 12 and 7, apply
plus to 1, minus to 6 at set and plus to 6,
minus to 1 at reset. Applied coil voltage
should be the same as the nominal.
Operating power will be reduced to one-
half.
CAUTIONS FOR USE
Based on regulations regarding insulation distance, there is a
restriction on same-channel load connections between terminals
No. 2, 3 and 4, 5, as well as between No. 8, 9 and 10, 11. See
the figure below for an example.
For Cautions for Use, see Relay Technical Information
.720 .024
.488 .024
.191 .012
18.3 0.6
12.4 0.6
.047 .012
4.85 0.3
1.2 0.3
.059 .012
1.5 0.3
1.276 .024
.200 .012
5.08 0.3
32.4 0.6
S Relay Socket,
S-PS
.059 .012
1.5 0.3
.610 .024
15.5 0.6
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Terminal width: 1.3
Terminal thickness: 1.2
.300 .012
7.62 0.3
Specifications
(Note: Don't insert or remove relays while in the energized condition.)
Breakdown voltage
Insulation resistance
Heat resistance
Maximum continuous current
.016 .004
0.4 0.1
.134 .012
3.4 0.3
Reset position of 2a2b type
-
.051
12
1
.047
11
2
Rib
10
3
Fig. 3
4
9
• Between 2, 3 and 4, 5:
• Between 10, 11 and 8, 9:
Fig. 1
Fig. 2
5
8
6
11
7
+
2 3
More than 100 M
10
No good
different channels, therefore not possible
different channels, therefore not possible
PC board pattern (Copper-side view)
12-.063 DIA. HOLE
12-1.6 DIA. HOLE
4
9
150 3 C
5
1,500 Vrms between terminals
2. Soldering operations should be
accomplished as quick as possible;
within 10 seconds at 250 C
temperature or 3 seconds at 350 C
662
with epoxy resin, undue subjection to
heat may cause loss of seal. Solder
should not be permitted to remain on the
header.
8
.299
7.6
F. The header portion being sealed
between terminals at 500 V DC Mega
(302 5.4
.200
5.08
.200
5.08
4 A
• Between 2, 3 and 4, 5:
• Between 10, 11 and 8, 9:
5.08
.200
F) for 1 hour.
5.08
.200
11
.200
5.08
2
10
3
Good
same channels, therefore possible
same channels, therefore possible
482 F
4
9
5
8
mm
solder
inch
S