SP2-L2-DC12V PANASONIC EW, SP2-L2-DC12V Datasheet - Page 3

• Manufacturer Part Number: SP2-L2-DC12V
• Description: POWER RELAY, DPDT, 12VDC, 15A, PLUG IN
• Manufacturer: PANASONIC EW

Specifications of SP2-L2-DC12V

• Relay Type: High Sensitivity
• Coil Voltage Vdc Nom: 12V
• Contact Current Max: 15A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 480ohm
• Contact Configuration: DPDT
• Coil Type: DC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2. Specifications
*1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load.
*2Refer to “6. Usage, Storage and Transport Conditions“ in
ds_61A08_en_sp: 300108D
Contact
Rating
Electrical
characteristics
Mechanical
characteristics
Expected life
Conditions
Unit weight
Characteristics
Initial contact pressure
Arrangement
Initial contact resistance, max.
Contact material
Nominal switching capacity (resistive load)
Max. switching power (resistive load)
Max. switching voltage
Max. switching current
Minimum operating power
Nominal operating power
Min. switching capacity (Reference value)
Insulation resistance (Initial)
(25C, 50% relative humidity)
Breakdown voltage
(Initial)
Operate time [Set time] (at 20C 68F)
Release time [Reset time] (at 20C 68F)
Temperature rise (at 20C 68F)
Shock resistance
Vibration resistance
Mechanical
Electrical (resistive load)
Conditions for operation, transport and storage
Max. operating speed
Between open contacts
Between contact and coil
Between contact sets
Functional
Destructive
Functional
Destructive
Item
AMBIENT ENVIRONMENT section in Relay Technical
*1
*2
2 Form C: Approx. 0.392 N (40 g
2 Form C, 4 Form C
Max. 30 m (By voltage drop 6 V DC 1A)
Stationary contact: Au flashed AgSnO
2 Form C: 15 A 250 V AC, 4 Form C: 10 A 250 V AC
2 Form C: 3,750 VA, 300 W, 4 Form C: 2,500 VA, 300 W
2 Form C, 4 Form C: 250 V AC, 30 V DC (48V DC: Max. 2A)
2 Form C: 15 A (AC) 10 A (DC), 4 Form C: 10 A
150mW (Single side stable, 2 coil latching)
300mW (Single side stable, 2 coil latching)
100 mA 5V DC
Min. 1,000M (at 500V DC)
Measurement at same location as “Initial breakdown voltage” section.
1,500 Vrms for 1 min. (Detection current: 10 mA)
3,000 Vrms for 1 min. (Detection current: 10 mA)
3,000 Vrms for 1 min. (Detection current: 10 mA)
Max. 30 ms [Max. 30 ms]
(Nominal voltage applied to the coil, excluding contact bounce time.)
Max. 20 ms [Max. 30 ms]
(Nominal voltage applied to the coil, excluding contact bounce time.) (without diode)
Max. 40C
(By resistive method, nominal voltage applied to the coil; nominal switching capacity.)
Min. 392 m/s
Min. 980 m/s
10 to 55 Hz at double amplitude of 3 mm (Detection time: 10s.)
10 to 55 Hz at double amplitude of 3 mm
Min. 510
2 Form C: Min. 10
4 Form C: Min. 10
Ambient temperature: –50C to +60C
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 cpm (at rated load)
2 Form C: 50 g
7
(at 180 cpm)
2
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10s.)
(Half-wave pulse of sine wave: 6 ms.)
1.76
5
5
(15 A 250 V AC [at 20 cpm]), Min. 10
(15 A 250 V AC [at 20 cpm]), Min. 10
oz; 4 Form C: 65 g
1.41
Information.
2
oz), 4 Form C: Approx. 0.196 N (20 g
Specifications
–58F to
type, Movable contact: AgSnO
2.29 oz
+140F;
5
5
(10 A 30 V DC [at 20 cpm])
(10 A 30 V DC [at 20 cpm])
2
type
0.71
oz)
SP
3