PIC18F4680-E/PT Microchip Technology, PIC18F4680-E/PT Datasheet - Page 20
![IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TQFP,44PIN,PLASTIC](/photos/6/82/68251/c04-076_pt_sml.jpg)
PIC18F4680-E/PT
Manufacturer Part Number
PIC18F4680-E/PT
Description
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TQFP,44PIN,PLASTIC
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC18F2221-ISO.pdf
(46 pages)
3.PIC18F4585-IPT.pdf
(482 pages)
4.PIC18F4585-IPT.pdf
(14 pages)
5.PIC18F4585-IPT.pdf
(8 pages)
6.PIC18F4585-IPT.pdf
(12 pages)
7.PIC18F4585-IPT.pdf
(4 pages)
Specifications of PIC18F4680-E/PT
Rohs Compliant
YES
Core Processor
PIC
Core Size
8-Bit
Speed
25MHz
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
36
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
3.25K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
44-TQFP, 44-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
I3-DB18F4680 - BOARD DAUGHTER ICEPIC3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F4680-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC18F2XXX/4XXX FAMILY
3.3
Data EEPROM is accessed one byte at a time via an
Address Pointer (register pair: EEADRH:EEADR) and
a data latch (EEDATA). Data EEPROM is written by
loading EEADRH:EEADR with the desired memory
location, EEDATA, with the data to be written and initi-
ating a memory write by appropriately configuring the
EECON1 register. A byte write automatically erases the
location and writes the new data (erase-before-write).
When using the EECON1 register to perform a data
EEPROM write, both the EEPGD and CFGS bits must
be cleared (EECON1<7:6> = 00). The WREN bit must
be set (EECON1<2> = 1) to enable writes of any sort
and this must be done prior to initiating a write
sequence. The write sequence is initiated by setting the
WR bit (EECON1<1> = 1).
The write begins on the falling edge of the 4th PGC
after the WR bit is set. It ends when the WR bit is
cleared by hardware.
FIGURE 3-7:
DS39622L-page 20
PIC18F2410
PIC18F2450
PIC18F2510
PIC18F2515
PIC18F2610
Note:
PGC
PGD
Poll WR bit
Data EEPROM Programming
4-Bit Command
1
0
Data EEPROM programming is not
available on the the following devices:
2
0
3
0
4
0
PGC
PGD
P5
DATA EEPROM WRITE TIMING
BSF EECON1, WR
1
4-Bit Command
PIC18F4410
PIC18F4450
PIC18F4510
PIC18F4515
PIC18F4610
2
1
0
2
0
15 16
3
0
4
0
P5A
P5
MOVF EECON1, W, 0
1
2
PGD = Input
PGD = Input
15 16
P5A
4-Bit Command
1
Poll WR bit, Repeat until Clear
0
After the programming sequence terminates, PGC must
still be held low for the time specified by Parameter P10
to allow high-voltage discharge of the memory array.
FIGURE 3-6:
2
0
3
0
P11A
(see below)
4
0
P5
MOVWF TABLAT
1
No
2
15 16
PROGRAM DATA FLOW
Enable Write
Set Address
Start Write
Sequence
2010 Microchip Technology Inc.
Set Data
Done?
WR bit
clear?
Done
Start
P5A
Yes
Yes
(see Figure 4-4)
PGD = Output
Shift Out Data
No
P10
16-Bit Data
Payload
1
n
2
n