PIC16F876A-E/SS Microchip Technology, PIC16F876A-E/SS Datasheet - Page 3

• Manufacturer Part Number: PIC16F876A-E/SS
• Description: 28 PIN, 14KB ENH FLASH, 368 RAM, 22 I/O,
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F876A-E/SS

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SSOP
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3. Module: Core
4. Module: A/D (Operation)
 2003 Microchip Technology Inc.
Certain code sequence and placement may cause
the corruption of a few bits in the instruction fetch
when the part is used above 4 MHz. A corrupted
instruction fetch will cause the part to execute an
improper instruction and result in unpredictable
outputs.
Microchip cannot predict which code sequences
and placement will cause this failure. If this failure
mechanism exists in your system, it should be evi-
dent during statistically significant preproduction
testing (minimum suggested sample size 100
units) of your particular code sequence and
placement.
Any code change should be tested in the same
manner prior to their implementation. If most parts
fail your tests, or if failures are seen at all voltages
or at all frequencies, this indicates that the problem
experienced does not relate to this failure
mechanism.
This problem has not been observed at operating
frequencies below 4 MHz.
Work around
Use the part at or below 4 MHz.
This problem is specific to Rev. B0 and has been
resolved by Rev. B2 of the silicon (date codes later
than 0242xxx).
The ADC is disabled when ADCON1<3:0> = 011x
(all inputs digital) and CMCON<2:0> = 111
(comparators are off).
This is a special case that conflicts with the second
sentence of Note 1 on page 131 of the device data
sheet: “Pins configured as digital inputs will
convert an analog input.”
Work around
For the ADC module to be enabled, it is necessary
to either:
1. Enable the comparators (CMCON<2:0> ≠ 111).
2. Configure at least one ADC channel as an
analog input (ADCON1<3:0> ≠ 011x).
Clarifications/Corrections to the Data
Sheet:
In the Device Data Sheet (DS39582B), the following
clarifications and corrections should be noted.
None.
PIC16F87XA
DS80128F-page 3