MCP1316MT-29LE/OT Microchip Technology, MCP1316MT-29LE/OT Datasheet - Page 2

• Manufacturer Part Number: MCP1316MT-29LE/OT
• Description: IC,VOLT DETECTOR,FIXED,+2.9V,TSOP,5PIN,PLASTIC
• Manufacturer: Microchip Technology
• Type: Simple Reset/Power-On Resetr

Specifications of MCP1316MT-29LE/OT

• Rohs Compliant: YES
• Number Of Voltages Monitored: 1
• Output: Open Drain or Open Collector
• Reset: Active Low
• Reset Timeout: 140 ms Minimum
• Voltage - Threshold: 2.9V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Monitored Voltage: 2 V to 4.7 V
• Output Type: Active Low, Open Drain
• Manual Reset: Resettable
• Watchdog: Watchdog
• Battery Backup Switching: No Backup
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1 V
• Supply Current (typ): 10 uA
• Maximum Power Dissipation: 240 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Power Fail Detection: No
• Undervoltage Threshold: 2.857 V
• Overvoltage Threshold: 2.944 V
• Power-up Reset Delay (typ): 2240 ms
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

MCP131X/2X
1.0
Absolute Maximum Ratings†
Supply Voltage (V
Input current (V
Output current (RST) . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Voltage on all inputs and outputs, except Open-Drain RST
(with no internal pull-up resistor), w.r.t. V
Voltage on Open-Drain RST
(with no internal pull-up resistor) w.r.t. V
Storage temperature . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient temp. with power applied . . . . . . . .-40°C to +125°C
Maximum Junction temp. with power applied . . . . . . . . 150°C
Power Dissipation (T
ESD protection on all pins ..................................................≥ 4 kV
DC CHARACTERISTICS
DS21985B-page 2
Electrical Specifications: Unless otherwise indicated, all limits are specified for V
(only MCP1320, MCP1321, and MCP1322), T
Operating Voltage Range
Specified V
Operating Current:
Note 1:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (V
5-Pin SOT-23A .......................................................240 mW
2:
3:
4:
5:
6:
ELECTRICAL
CHARACTERISTICS
Trip point is ±1.5% from typical value.
Trip point is ±2.5% from typical value.
Hysterysis is minimum = 1%, maximum = 6% at +25°C.
This specification allows this device to be used in PIC
cuit Serial Programming™ (ICSP™) feature (see device-specific programming specifications for voltage
requirements). The total time that the RST pin can be above the maximum device operational voltage
(5.5V) is 100s. Current into the RST pin should be limited to 2 mA. It is recommended that the device oper-
ational temperature be maintained between 0°C to +70°C (+25°C preferred). For additional information,
refer to
This parameter is established by characterization and is not 100% tested.
Custom ordered voltage trip point; minimum order volume requirement. Information available upon request.
DD
Parameters
DD
Value to V
DD
) . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
A
to V
Figure
≤ 70°C):
SS
) . . . . . . . . . . . . . . . . . . . . . . 7.0V
OUT
2-35.
Low
SS
SS
. . -0.6V to 13.5V
Sym
V
V
I
DD
DD
DD
DD
A
+ 1.0V)
= -40°C to +125°C.
Min
1.0
1.0
—
—
—
—
Typ
—
—
5
1
1
5
† Notice: Stresses above those listed under “Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
®
microcontroller applications that require the In-Cir-
Max
5.5
10
10
—
2
2
Units
µA
µA
µA
µA
V
V
DD
I
Watchdog Timer Active
Watchdog Timer Inactive
V
Reset Delay Timer Active
= 1V to 5.5V, R
RST
© 2007 Microchip Technology Inc.
DD
< V
= 10 µA, V
TRIP
Conditions
PU
RST
= 100 kΩ
< 0.3V