CS4362-KQZ Cirrus Logic Inc, CS4362-KQZ Datasheet - Page 26
![IC,Audio Processor,QFP,48PIN,PLASTIC](/photos/6/68/66856/mfg_cs4362_series_sml.jpg)
CS4362-KQZ
Manufacturer Part Number
CS4362-KQZ
Description
IC,Audio Processor,QFP,48PIN,PLASTIC
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS4362-KQZ.pdf
(42 pages)
Specifications of CS4362-KQZ
Number Of Bits
24
Data Interface
Serial
Number Of Converters
6
Voltage Supply Source
Analog and Digital
Power Dissipation (max)
390mW
Operating Temperature
-10°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Settling Time
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
598-1644
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS4362-KQZR
Manufacturer:
STM
Quantity:
2 332
26
VQ
FILT+
AOUTA1 +,-
AOUTB1 +,-
AOUTA2 +,-
AOUTB2 +,-
AOUTA3 +,-
AOUTB3 +,-
MUTEC1
MUTEC2
MUTEC3
MUTEC4
MUTEC5
MUTEC6
Stand-Alone Definitions
M0
M1
M2
M3
Control Port Definitions
SCL/CCLK
SDA/CDIN
AD0/CS
DSD Definitions
DSDA1
DSDB1
DSDA2
DSDB2
DSDA3
DSDB3
DSD_SCLK
DSD_EN
Pin Name
39,40
38,37
35,36
34,33
29,30
28,27
21
20
41
26
25
24
23
22
17
16
15
42
15
16
17
48
47
46
42
#
3
2
1
7
Quiescent Voltage (Output) - Filter connection for internal quiescent voltage. VQ must be
capacitively coupled to analog ground, as shown in the Typical Connection Diagram. The nom-
inal voltage level is specified in the Analog Characteristics and Specifications section. VQ pre-
sents an appreciable source impedance and any current drawn from this pin will alter device
performance. However, VQ can be used to bias the analog circuitry assuming there is no AC
signal component and the DC current is less then the maximum specified in the Analog Charac-
teristics and Specifications section.
Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling cir-
cuits. Requires the capacitive decoupling to analog ground as shown in the Typical Connection
Diagram.
Differential Analog Output (Output) - The full-scale differential analog output level is specified
in the Analog Characteristics specification table.
Mute Control (Output) - The Mute Control pins go high during power-up initialization, reset,
muting, power-down or if the master clock to left/right clock frequency ratio is incorrect. These
pins are intended to be used as a control for external mute circuits on the line outputs to prevent
the clicks and pops that can occur in any single supply system. Use of Mute Control is not man-
datory but recommended for designs requiring the absolute minimum in extraneous clicks and
pops.
Mode Selection (Input) - Determines the operational mode of the device as detailed in
Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external
pull-up resistor to the logic interface voltage in I²C Mode as shown in the Typical Connection
Diagram.
Serial Control Port Data (Input/Output) - SDA is a data I/O line in I²C Mode and is open drain,
requiring an external pull-up resistor to the logic interface voltage, as shown in the Typical Con-
nection Diagram; CDIN is the input data line for the control port interface in SPI Mode.
Address Bit 0 (I²C) / Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I²C
Mode; CS is the chip select signal for SPI Mode.
Direct Stream Digital Input (Input) - Input for Direct Stream Digital serial audio data.
DSD Serial Clock (Input) - Serial clock for the Direct Stream Digital serial audio interface.
DSD Enable (Input) - When held at logic ‘1’ the device will enter DSD Mode (Stand-Alone Mode
and 7.
only).
Pin Description
CS4362
DS257F2
Tables 6