ADG1409YRUZ Analog Devices Inc, ADG1409YRUZ Datasheet - Page 16

• Manufacturer Part Number: ADG1409YRUZ
• Description: IC, ANALOG MULTIPLEXER, DUAL 4X1 TSSOP16
• Manufacturer: Analog Devices Inc
• Series: iCMOS®r
• Type: Analog Multiplexerr

Specifications of ADG1409YRUZ

• No. Of Circuits: 2
• Supply Current: 220µA
• On State Resistance Max: 4ohm
• Supply Voltage Range: ± 4.5V To ± 5.5V, 10.8V To 13.2V, ± 13.5V To ± 16.5V
• Operating Temperature Range: -40°C To +125°C
• Function: Multiplexer
• Circuit: 2 x 4:1
• On-state Resistance: 4.7 Ohm
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 12V, 15V
• Current - Supply: 1µA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP (0.173", 4.40mm Width)
• Multiplexer Configuration: Dual 4:1
• Number Of Inputs: 8
• Number Of Outputs: 2
• Number Of Channels: 2
• Analog Switch On Resistance: 9@±4.5VOhm
• Analog Switch Turn On Time: 330ns
• Analog Switch Turn Off Time: 285ns
• Package Type: TSSOP
• Power Supply Requirement: Single/Dual
• Single Supply Voltage (min): 5V
• Single Supply Voltage (typ): 12V
• Single Supply Voltage (max): 16.5V
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (typ): ±5/±15V
• Dual Supply Voltage (max): ±16.5V
• Mounting: Surface Mount
• Pin Count: 16
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

ADG1408/ADG1409
TERMINOLOGY
R
Ohmic resistance between D and S.
ΔR
Difference between the R
R
Flatness is defined as the difference between the maximum and
minimum value of on resistance as measured.
I
Source leakage current when the switch is off.
I
Drain leakage current when the switch is off.
I
Channel leakage current when the switch is on.
V
Analog voltage on Terminal D and Terminal S.
C
Channel input capacitance for off condition.
C
Channel output capacitance for off condition.
C
On switch capacitance.
C
Digital input capacitance.
t
Delay time between the 50% and 90% points of the digital input
and switch on condition.
t
Delay time between the 50% and 90% points of the digital input
and switch off condition.
t
Delay time between the 50% and 90% points of the digital
inputs and the switch on condition when switching from one
address state to another.
S
D
D
ON
OFF
TRANSITION
ON
FLAT(ON)
S
D
D
IN
D
, I
(Off)
(Off)
, C
(Off)
ON
(V
(Off)
(EN)
(EN)
S
(On)
S
S
)
(On)
ON
of any two channels.
Rev. B | Page 16 of 20
t
Off time measured between the 80% point of both switches
when switching from one address state to another.
V
Maximum input voltage for Logic 0.
V
Minimum input voltage for Logic 1.
I
Input current of the digital input.
I
Positive supply current.
I
Negative supply current.
Off Isolation
A measure of unwanted signal coupling through an off channel.
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching.
Bandwidth
Frequency at which the output is attenuated by 3 dB.
On Response
Frequency response of the on switch.
Total Harmonic Distortion Plus Noise (THD + N)
Ratio of the harmonic amplitude plus noise of the signal to the
fundamental.
AC Power Supply Rejection Ratio (ACPSRR)
A measure of the ability of a part to avoid coupling noise and
spurious signals that appear on the supply voltage pin to the
output of the switch. The dc voltage on the device is modulated
by a sine wave of 0.62 V p-p. The ratio of the amplitude of
signal on the output to the amplitude of the modulation is
the ACPSRR.
BBM
INL
DD
SS
INL
INH
, I
INH