LM2674M-5.0 National Semiconductor, LM2674M-5.0 Datasheet - Page 19
![IC, STEP-DOWN REGULATOR, 8-SOIC](/photos/18/97/189768/3778330_sml.jpg)
LM2674M-5.0
Manufacturer Part Number
LM2674M-5.0
Description
IC, STEP-DOWN REGULATOR, 8-SOIC
Manufacturer
National Semiconductor
Datasheet
1.LM2674LD-3.3NOPB.pdf
(26 pages)
Specifications of LM2674M-5.0
Primary Input Voltage
12V
No. Of Outputs
1
Output Voltage
5V
Output Current
500mA
No. Of Pins
8
Operating Temperature Range
-40°C To +125°C
Supply Voltage Range
6.5V To 40V
Termination Type
SMD
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2674M-5.0/NOPB
Manufacturer:
TI
Quantity:
15 000
B. Select an appropriate capacitor value and voltage rating,
using the capacitor code, from the output capacitor selection
table in Figure 17. There are two solid tantalum (surface mount)
capacitor manufacturers and four electrolytic (through hole)
capacitor manufacturers to choose from. It is recommended that
both the manufacturers and the manufacturer’s series that are
listed in the table be used. A table listing the manufacturers’
phone numbers is located in Figure 11.
4. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is
the load current times the catch diode duty cycle, 1-D (D is the
switch duty cycle, which is approximately V
value of the catch diode average current occurs at the maximum
input voltage (minimum D). For normal operation, the catch
diode current rating must be at least 1.3 times greater than its
maximum average current. However, if the power supply design
must withstand a continuous output short, the diode should have
a current rating greater than the maximum current limit of the
LM2674. The most stressful condition for this diode is a shorted
output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
C. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency. The Schottky diode must be located close to the
LM2674 using short leads and short printed circuit traces.
LM2674 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)
PROCEDURE (Adjustable Output Voltage Version)
OUT
/V
IN
). The largest
19
B. From the output capacitor selection table in Figure 17,
choose a capacitor value (and voltage rating) that intersects the
capacitor code(s) selected in section A, C20.
The capacitance and voltage rating values corresponding to the
capacitor code C20 are the:
Surface Mount:
33 µF/25V Sprague 594D Series.
33 µF/25V AVX TPS Series.
Through Hole:
33 µF/25V Sanyo OS-CON SC Series.
120 µF/35V Sanyo MV-GX Series.
120 µF/35V Nichicon PL Series.
120 µF/35V Panasonic HFQ Series.
Other manufacturers or other types of capacitors may also be
used, provided the capacitor specifications (especially the 100
kHz ESR) closely match the characteristics of the capacitors
listed in the output capacitor table. Refer to the capacitor
manufacturers’ data sheet for this information.
4. Catch Diode Selection (D1)
A. Refer to the table shown in Figure 12. Schottky diodes
provide the best performance, and in this example a 500mA,
40V Schottky diode would be a good choice. If the circuit must
withstand a continuous shorted output, a higher current (at least
1.2A) Schottky diode is recommended.
EXAMPLE (Adjustable Output Voltage Version)
www.national.com