LT3694EUFD#PBF Linear Technology, LT3694EUFD#PBF Datasheet - Page 4

• Manufacturer Part Number: LT3694EUFD#PBF
• Description: IC, DC-DC CONV, 2.5MHz, QFN28
• Manufacturer: Linear Technology

Specifications of LT3694EUFD#PBF

• Primary Input Voltage: 36V
• No. Of Outputs: 3
• Output Current: 2.6A
• No. Of Pins: 28
• Operating Temperature Range: -40°C To +125°C
• Peak Reflow Compatible (260 C): Yes
• Switching Frequency Max: 2.5MHz
• Msl: MSL 1 - Unlimited
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LT3694/LT3694-1
ELECTRICAL CHARACTERISTICS
PARAMETER
LDO Regulator
Feedback Pin Voltage
Feedback Pin Bias Current
Error Amplifier Voltage Gain
TRK/SS Pull-Up Current
TRK/SS Threshold to Shut Down LDO
Line Regulation
Load Regulation
Base Drive
Current Limit Threshold
Short-Circuit Current Limit Threshold
Minimum BIAS to DRV Voltage (Note 7)
Minimum V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3694E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3694I is guaranteed to meet performance specifications from –40°C to
125°C junction temperature.
Note 3: Current limit is guaranteed by design and/or correlation to static
test. Slope compensation reduces current limit at higher duty cycles.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
4
temperature range, otherwise specifications are at T
IN
to DRV Voltage
A
= 25°C, V
CONDITIONS
5V < V
I
V
I
I
DRV
DRV
DRV
FB
The
= 0
From 0.1mA to 10mA
= 10mA
= 10mA
IN
l
< 36V
IN
denotes the specifications which apply over the full operating
= 12V, V
Note 5: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions.
Junction temperature will exceed the maximum operating range when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair
device reliability.
Note 6: Absolute Maximum Voltage at V
non-repetitive, 1 second transients and 36V for continuous operation.
Note 7: The LDO will function if the BIAS to DRV differential is not met,
but the base drive current will be drawn from V
Note 8: The PGOOD pin will pull low when the voltage on any of the three
FB pins is lower than the PGOOD threshold value.
Note 9: Positive currents flow into pins, negative currents flow out of pins.
Minimum and maximum values refer to absolute values.
BIAS
= 3V, unless otherwise noted. (Notes 2, 9)
l
l
l
l
l
l
MIN
735
–2
35
10
47
22
IN
and EN/UVLO pins is 70V for
0.025
2800
IN
TYP
750
–50
0.5
0.3
2.0
–3
50
15
60
26
instead of BIAS.
–500
MAX
765
0.9
2.3
–4
70
20
70
30
mV/mA
UNITS
36941fa
%/V
mV
mV
mA
mV
mV
nA
μA
V
V