SC600CIMLTR Semtech, SC600CIMLTR Datasheet - Page 7
![IC, LED DRIVER, CHARGE PUMP, MLPD-10](/photos/19/2/190239/4551591_sml.jpg)
SC600CIMLTR
Manufacturer Part Number
SC600CIMLTR
Description
IC, LED DRIVER, CHARGE PUMP, MLPD-10
Manufacturer
Semtech
Datasheet
1.SC600BIMLTRT.pdf
(19 pages)
Specifications of SC600CIMLTR
Led Driver Application
LED Backlighting, Portable Electronics
No. Of Outputs
1
Output Current
60mA
Output Voltage
4.725V
Input Voltage
2.5V To 6.5V
Topology
Charge Pump
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Regulated Fractional Charge Pump Operation
A fractional charge pump is a voltage converter which
implements switched capacitor techniques to produce an
output voltage that is one of several multiples of the input
voltage. Regulated fractional charge pumps (also called
charge pump regulators) use a linear regulator with vari-
ous charge pump confi gurations to deliver a regulated out-
put over a wide input voltage range. Regulated fractional
charge pumps have improved effi ciency over ordinary lin-
ear regulator and charge pump circuit combinations. The
improved effi ciency is achieved by implementing multiple
charge pump confi gurations on one integrated circuit.
The correct charge pump confi guration is automatically
selected to meet the regulation requirements at the best
possible effi ciency. The SC600 has three charge pump
confi gurations (modes), which multiply the input voltage
by 1x, 1.5x and 2x.
The charge pump confi gurations are implemented with
two switched or 'bucket' capacitors plus the input and out-
put capacitor. The bucket capacitors are confi gured for 1x
mode at start-up to source current to the output capacitor
and bring the output up quickly. The charge pump will
begin switching in 1.5x mode. During normal operation,
starting with a fully charged Li-Ion cell, the battery voltage
will begin at about 4.1V. As the battery discharges and
the voltage decays, the SC600 will eventually transition to
2x mode when the battery voltage is approximately 3.50V.
Hysteresis is provided to prevent mode toggling. The out-
put is prevented from exceeding 6.0V. This feature allows
the use of 6.3V ceramic capacitors.
mAhXLiFE
The plot on page 1 shows the effi ciency of the SC600A.
An example of a 5.0V regulated charge pump doubler is
plotted to demonstrate how effective the SC600’s 1.5x
mode is at improving effi ciency when the input voltage is
above 3.5V. Most of the Li-Ion battery life is above 3.5V
where the SC600 achieves more than 20% higher effi -
ciency compared to the 5.0V regulated charge pump dou-
bler with only a 2x mode. Following the effi ciency curve
from left to right as the battery discharges, the SC600A
5.0V remains in 1.5x mode until 3.5V and then transitions
to 2x mode.
POWER MANAGEMENT
Applications Information
© 2006 Semtech Corp.
TM
Advantage
7
Component Versions
There are four versions of the SC600. The component
selection table on page 4 highlights the differences be-
tween the component types. The three basic differences
between the component versions are in the output volt-
age, maximum output current capability, and the mode
transition point.
The mode transition point is the value of input voltage at
which the component will transition between 1.5x and 2x
modes. 5.0V, 4.5V, and 4.0V versions are available. The
SC600A (5.0V) is most effi cient for applications that use
up to 60mA. The SC600B (4.5V) and SC600C (4.5V) have
different maximum output currents and mode transition
points. The lower mode transition point of the SC600C
allows it to remain in 1.5x mode longer for greater power
savings.
The SC600B has higher output capability, up to 120mA,
and S600C is rated for 60mA. The SC600D (4.0V) is for
applications using up to 120mA.
Start-Up Conditions
Typical start-up time is less than 50μs.
must be enabled while 650kHz or 262kHz is selected to pre-
vent over-voltage during start-up.
LED Bias and Backlighting Applications
When using the SC600 for LED bias, note that the SC600C
and SC600D require the same input power per unit of
output current even though the SC600C is more effi cient.
Also, the SC600A will have the same input power as the
SC600B though the SC600A is more effi cient.
The following plots of Input Power vs. Input Voltage high-
light the differences in application of the four component
versions. To achieve the lowest possible input power, it
is desirable for the charge pump to remain in 1.5x mode
until the input voltage is as low as possible. The transi-
tion points from 1.5x to 2x are identifi ed in the plot where
the input power steps upward as the input voltage moves
lower.
Caution: The SC600
www.semtech.com
SC600