TC9400CPD TELCOM SEMICONDUCTOR, TC9400CPD Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
TC9400CPD
Manufacturer Part Number
TC9400CPD
Description
IC, F/V-V/F CONVERTER, 9400, DIP14
Manufacturer
TELCOM SEMICONDUCTOR
Datasheet
1.TC9400CPD.pdf
(20 pages)
Specifications of TC9400CPD
Frequency
100kHz
Linearity %
0.05%
Supply Voltage Range
± 4V To ± 7.5V
Digital Ic Case Style
DIP
No. Of Pins
14
Operating Temperature Max
70°C
Operating Temperature Min
0°C
Package /
RoHS Compliant
Full Scale Range
10Hz To 100kHz
Rohs Compliant
Yes
Bandwidth
100kHz
Base Number
9400
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TC9400CPD
Manufacturer:
MIT
Quantity:
6 234
Part Number:
TC9400CPD
Manufacturer:
TELCOM
Quantity:
20 000
TC9400/9401/9402
3.2
The TC9400 output can be measured in the time
domain as well as the frequency domain. Some micro-
computers, for example, have extensive timing capabil-
ity, but limited counter capability. Also, the response
time of a time domain measurement is only the period
between two output pulses, while the frequency mea-
surement must accumulate pulses during the entire
counter time-base period.
Time measurements can be made from either the
TC9400's PULSE FREQ OUT output, or from the
FREQ/2 OUT output. The FREQ/2 OUT output
changes state on the rising edge of PULSE FREQ
OUT, so FREQ/2 OUT is a symmetrical square wave at
one-half the pulse output frequency. Timing measure-
ments can, therefore, be made between successive
PULSE FREQ OUT pulses, or while FREQ/2 OUT is
high (or low).
FIGURE 4-1:
DS21483B-page 8
Voltage-to-Time Measurements
F
Amp Out
OUT
F
OUT
/2
Notes: 1. To adjust F
OUTPUT WAVEFORMS
2. To adjust F
3. To increase F
4. For high performance applications, use high stability components for R
resistors and glass capacitors). Also, separate output ground (Pin 9) from input ground (Pin 6).
1/f
MIN
MAX
OUT
, set V
3µsec
Typ.
, set V
MAX
IN
IN
to 100kHz, change C
= 10mV and adjust the 50kΩ offset for 10Hz output.
= 10V and adjust R
REF
IN
4.0
4.1
In the V/F mode, this input is connected to the AMPLI-
FIER OUT output (Pin 12) and triggers a 3µsec pulse
when the input voltage passes through its threshold. In
the F/V mode, the input frequency is applied to this
input.
The nominal threshold of the detector is half way
between the power supplies, or (V
The TC9400's charge balancing V/F technique is not
dependent on a precision comparator threshold,
because the threshold only sets the lower limit of the
Op Amp output. The Op Amp's peak-to-peak output
swing, which determines the frequency, is only
influenced by external capacitors and by V
4.2
This output is an open drain N-channel FET, which pro-
vides a pulse waveform whose frequency is propor-
tional to the input voltage. This output requires a pull-
up resistor and interfaces directly with MOS, CMOS,
and TTL logic (see Figure 4-1).
or V
to 2pF and C
REF
for 10kHz output.
PIN FUNCTIONS
Threshold Detector Input
Pulse Freq Out
INT
to 75pF.
IN
, C
REF
©
2002 Microchip Technology Inc.
, V
REF
V
0V
(metal film
DD
REF
+ V
C
C
SS
REF
INT
)/2 ±400mV.
REF
.