622-025-260-042 EDAC Inc, 622-025-260-042 Datasheet - Page 31

• Manufacturer Part Number: 622-025-260-042
• Description: CONN D SUB RCPT 25POS R/A .318
• Manufacturer: EDAC Inc
• Series: 622r

Specifications of 622-025-260-042

• Current Rating: 5A
• Connector Style: D-Sub
• Number Of Positions: 25
• Number Of Rows: 2
• Shell Size, Connector Layout: 3 (DB, B)
• Contact Type: Signal
• Connector Type: Receptacle, Female Sockets
• Mounting Type: Panel Mount; Through Hole, Right Angle
• Flange Feature: Housing/Shell (4-40)
• Termination: Solder
• Features: Board Lock, Shielded
• Shell Material, Finish: Steel, Nickel Plated
• Contact Finish: Gold
• Contact Finish Thickness: Flash
• Operating Temperature: -55°C ~ 105°C
• Housing Material: Polyester
• Color: Black
• Product: Standard Hoods & Connectors
• Number Of Positions / Contacts: 25
• Contact Plating: Gold
• Shell Plating: Nickel
• Gender: Male
• Mounting Style: Right Angle
• Mounting Angle: Right
• Termination Style: Crimp
• Pitch: 2.77 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

SPECIAL VARIATION CONNECTORS
SPECIAL VARIATION ID CODE
UNIQUE LISTING CODE
•
•
•
•
•
•
•
•
•
•
•
•
For over 30 years EDAC has manufactured a
wide selection of special connectors. In the
part numbering system, they are identified as
special by the last group of digits in the part
number.
No.3 - for Series 100 to 438
No.9 - for Series 516 to 746
This number is assigned by EDAC. Note that
connector part number 345-015-274-900
may have completely different features than
the part number in the above example.
Some examples of special connector features
previously used in manufacturing include:
Special contact assembly patterns.
Polarizing key installed or molded into position.
Cost saving options such as no part marking.
Material and plating options.
Special insulator dimensions (length, width,
height, mounting).
Insulator features such as open card slot ends.
Special contact bends, boardlock forms, tail
lengths.
Customer part number marking.
Specific quality requirements or testing.
Specific control on insertion and withdrawal
forces.
Mounting features such as side holes through
card guides.
Special rack and panel polarization or cover
designs.
If you have any unique or unusual connector
requirements, discuss them with the
specialists at EDAC, where your connector
needs can become reality.
Example:
345-015-274-901
ENGINEERING NOTES
32
ENVIRONMENTAL RESPONSIBILITY
GENERAL NOTES
1
2
AWG ..................American Wire Gauge
C.......................Celsius
CSA...................Canadian Standards Association
Dia. ..................Diameter
EISA ..................Extended Industry Standard
ID......................Inside Diameter
ISA ....................Industry Standard Architecture
kN.....................Kilonewton
kPa ...................Kilopascal
lbs. ..................Pounds
MCA ..................Microchannel Architecture
mm ...................Millimetres
N ......................Newton
oz. ...................Ounce
PC.....................Printed Circuit
P/N....................Part Number
psi.....................Pounds per square inch
rms ...................Root mean squared
V AC..................Volts, Alternating Current
UL .....................Underwriters Laboratories
UNC ..................Unified Coarse
µ” .....................Microinches
µm ...................Microns
5
6
EDAC’s products and manufacturing processes
are free of ozone depleting substances (CFCs
and HCFCs) as listed by the Environmental
Protection Agency. In addition, waste water
quality management and 3R (reduce, reuse and
recycle) programs form part of the EDAC
commitment to environmental responsibility.
EDAC is a licensed user of the connector design
technology that permits the use of flat rock
tooling for the installation of the compliant pin
card edge connectors.
Every effort has been made to ensure the
accuracy of information within this catalog.
When changes or corrections are necessary,
trade announcements are made to customers,
distributors or representatives of EDAC. Readers
of this catalog are invited to offer suggestions
for improvements to future publications.
Dimensional drawings are presented using
Abbreviations used in this catalog include:
orthographic third angle projection.
Architecture