LF13WBP-11P HRS (HIROSE), LF13WBP-11P Datasheet - Page 10
![PLUG, MALE PIN, 11WAY](/photos/18/87/188721/151875207-40_sml.jpg)
LF13WBP-11P
Manufacturer Part Number
LF13WBP-11P
Description
PLUG, MALE PIN, 11WAY
Manufacturer
HRS (HIROSE)
Datasheet
1.LF13WBJ-11P.pdf
(11 pages)
Specifications of LF13WBP-11P
Connector Body Material
Zinc Alloy
Gender
Plug
Connector Mounting
Cable Mount
Connector Shell Size
13
Insert Arrangement
13-11
No. Of Contacts
11
Contact
RoHS Compliant
Connector Type
Circular Industrial
Contact Termination
Solder
Rohs Compliant
Yes
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
10
LF Series●Miniature Waterproof Shielded Connectors
No.
5
6
3
5
5
1
,
,
4
2
Threaded section
Forming cavity
Groove
Table 6
Shell size
LF07
LF10
LF13
Wrench width : D
Illustration
Tightening torque Wrench width
Backshell
1N · m~1.5N · m
1N · m~1.5N · m
1.5N · m~2N · m
Threaded section
Tightening collar
Tightening collar
Seal bushing
Crimping tool
Strain relief collar
Protrusion
10mm
13mm
16mm
Note
Note
Connector Assembly
4
HR10A-TC-02
3
5
5
Crimping tool
1
2
LF-TC-01
For plug assembly
For jack assembly
Both sides of the shielding clamp must be
placed in the forming cavity of the tool
(as shown on the illustration) and crimped
over the cable by closing the tool completely.
Place the body/insulator assembly in the
applicable solder termination fixture.
Coat the thread section of the body/insulator
assembly with Loctite 271 compound
(manufactured by Henckel Japan, Ltd.) or
equivalent, tightening it with a torque
specified in the table 6.
Slide forward the seal bushing and insert it in
the backshell until fully seated.
Slide forward the strain relief collar and insert
it in the backshell, making sure that the
opposing protrusions fit inside the
corresponding grooves, as shown on the
illustration.
Verify that the Locktite 7649 primer
(or equivalent) on the threaded sections of the
backshell and tightening collar are dry.
Apply the Locktite 271 compound to the
tightening collar’s threaded section and attach
it to the backshell.
It is critical that the cable itself will not turn or
twist during this operation.
It is critical that the protrusions are inside the
corresponding grooves.
Fixture Part No.
Fixture Part No.
LF07BP-T01
LF10BP-T01
LF13BP-T01
LF07BJ-T01
LF10BJ-T01
LF13BJ-T01
Forming cavity
5.3
7.0
7.9
9.1
Operation
LF07WBP-6S,6P,3S,3P
LF10WBP-4S,4P,12S,12P
LF13WBP-20S,20P,11S,11P
LF07WBJ-6S,6P,3S,3P
LF10WBJ-4S,4P,12S,12P
LF13WBJ-20S,20P,11S,11P
Applicable connector
Applicable connector
Applicable cable
7.3mm
8.7mm
diameter
5mm
–––
diameter after crimping
Shielding clamp
5.3mm to
7.9mm to
9.1mm to
5.5mm
8.1mm
9.3mm
–––