07.311.6155.0 WIELAND ELECTRIC, 07.311.6155.0 Datasheet - Page 499
![END PLATE, WK4TKG SERIES TERMINAL BLOCK](/photos/18/38/183889/4533506_sml.jpg)
07.311.6155.0
Manufacturer Part Number
07.311.6155.0
Description
END PLATE, WK4TKG SERIES TERMINAL BLOCK
Manufacturer
WIELAND ELECTRIC
Series
APr
Datasheet
1.07.311.6155.0.pdf
(900 pages)
Specifications of 07.311.6155.0
Color
Gray
Accessory Type
End Plate
For Use With
WK4TKG...DIST Series Terminal Blocks
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 499 of 900
- Download datasheet (63Mb)
dipos
dipos
2, 3 or 4 wire connection technology
for RTD/Pt sensors
The range provided by Wieland offers
devices for all connection technologies.
The appropriate technique is used,
depending on the accuracy requirement.
The individual measurement types are
described in detail as follows.
The obvious benefit of a 2-wire
connection lies in the minimum wiring
costs. It should however be noted that
greater errors can occur during
measurement using this method. In the
case of a Pt100 sensor, an additional
resistance of only one ohm is sufficient
for an error of 2.5°C. This error acts as an
offset (zero displacement). This type of
increase in resistance can be caused by
cable resistances, contact resistances,
soldered connections, plugs etc. In order
to compensate for these errors, the
Wieland modules offer a zero balance.
This does not however prevent errors
from occurring during operation that are
caused by variations in the ambient
temperature.
In practice, a 2-wire connection is only
recommended if the application does not
require a high level of accuracy.
In the case of a 3-wire connection, one of
the sensor cables is used for measuring
the cable and contact resistances. The
influence of the additional resistances can
thus be largely eliminated. This however
only applies under one condition which is
often not observed:
The resistances of the three cables and
the respective connectors must match
exactly.
A differential of 0.39 ohm already causes
an error of 1 degree (Pt100). Only the
respective state can be equalized by
carrying out an adjustment during
commissioning. It is not possible to
remedy the sources of error that are
caused by temperature.
In the case of 4-wire technology, two
cables take over the temperature
measurement and two further cables
measure at high resistance the voltage
drop that arises via the resistance-type
sensor.
All the effects caused by contact or cable
resistances are fully eliminated.
The error is maximum 0.004% per ohm.
There is practically no influence produced
on the output variable. It is irrelevant if
the resistances have different values and
are subjected to different conditions due
to the application.
497
Related parts for 07.311.6155.0
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![07.310.9653.0](/photos/18/38/183884/4371167_tmb.jpg)
Part Number:
Description:
End Plate
Manufacturer:
WIELAND ELECTRIC
Datasheet:
![07.311.0155.0](/photos/18/38/183885/4435345_tmb.jpg)
Part Number:
Description:
END PLATE, WK SERIES TERMINAL BLOCK
Manufacturer:
WIELAND ELECTRIC
Datasheet:
![07.311.0255.0](/photos/18/38/183885/4435345_tmb.jpg)
Part Number:
Description:
END PLATE, WK/WKN SERIES TERMINAL BLOCK
Manufacturer:
WIELAND ELECTRIC
Datasheet:
![07.311.1155.0](/photos/18/38/183886/4306408_tmb.jpg)
Part Number:
Description:
PARTITION PLATE WK SERIES TERMINAL BLOCK
Manufacturer:
WIELAND ELECTRIC
Datasheet: