E6H-CWZ6C 1000P/R 0.5M Omron, E6H-CWZ6C 1000P/R 0.5M Datasheet - Page 4

• Manufacturer Part Number: E6H-CWZ6C 1000P/R 0.5M
• Description: ENCODER ROTARY 5-24V 1000RES .5M
• Manufacturer: Omron
• Series: E6Hr

Specifications of E6H-CWZ6C 1000P/R 0.5M

• Encoder Type: Optical
• Output Type: Quadrature with Index (Incremental)
• Pulses Per Revolution: 1000
• Voltage - Supply: 5 ~ 24VDC
• Actuator Type: 8mm Open Center
• Detent: No
• Built In Switch: No
• Mounting Type: Chassis Mount, Motors
• Orientation: Vertical
• Termination Style: Cable Leads
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Rotational Life (cycles Min): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: E6H-CWZ6C1000P/R0.5M; E6HCWZ6C1000PR05M

Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use the Encoder under ambient conditions that exceed the
ratings.
● Mounting
Dimensions
E6H-C
• The diameter of the mating shaft must be 8
• The allowable displacement in the mating shaft must 0.05 mm in
• The mounting surface and shaft must be perpendicular to within
• When securing the Encoder, do not allow force to be applied to the
Rotary Encoder Recommended Power Supplies:
11 mm long from the mounting surface.
the radial direction and 0.3 mm in the thrust direction.
0.03 mm.
leaf spring.
Precautions for Correct Use
0.03 A
A
WARNING
Eccentricity will develop in the
Encoder if the above values are not
satisfied, and the mounting leaf spring
may be destroyed.
Allen set screws
Two, M3 × 4
screws
E6H-CWZ6C, E6H-CWZ3E
E6H-CWZ3X
4.2-dia. shielded cable with 5 conductors
(Conductor cross section: 0.1 mm
Insulator diameter: 0.88 mm), Standard
length: 500 mm
5.5-dia. shielded cable with 8 conductors
(Conductor cross section: 0.1 mm
Insulator diameter: 1.0 mm), Standard
length: 500 mm
Two,
6.4 dia.
Two, 3.2
Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.
−0.012
−0.004
Hollow shaft
(Hollow shaft interior
dia.: 8 mm)
+0.1
0
mm and 8 to
dia.
8
+0.015
0
2
2
,
,
dia.
Consult your OMRON representative for details.
7
10
26
● Wiring
Spurious pulses may be generated when power is turned ON and
OFF. Wait at least 0.1 s after turning ON the power to the Encoder
before using the connected device, and stop using the connected
device at least 0.1 s before turning OFF the power to the Encoder.
Also, turn ON the power to the load only after turning ON the power
to the Encoder.
• When securing the Encoder, use two M3 screws to secure the leaf
• Use the Allen set screw provided with the hollow shaft to secure the
• If wiring after securing the Encoder, do not pull on the cable. Also,
• If the Encoder phase Z must be aligned with the origin of the
spring to the mounting surface.
shaft. Use a tightening torque of 0.4 N·m and apply screw lock glue
to the screw to prevent it from becoming loose.
do not apply shock to the Encoder or hollow shaft.
installation device, mount the Encoder while checking the phase Z
output.
6
4.2 dia.
40 dia.
8 dia.
8
54
46
20˚
E6H-C
(Unit: mm)
4