MMA1260D Freescale Semiconductor, MMA1260D Datasheet - Page 3

• Manufacturer Part Number: MMA1260D
• Description: SENSOR ACCEL Z-AX +/-1.5G 16SOIC
• Manufacturer: Freescale Semiconductor
• Series: MMAr

Specifications of MMA1260D

• Axis: Z
• Acceleration Range: ±1.5g
• Sensitivity: 1200 mV/g
• Voltage - Supply: 4.75 V ~ 5.25 V
• Output Type: Analog
• Bandwidth: 50Hz
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• For Use With: RD1986MMA2260D - KIT SENSOR ACCEL MMA2260D TRIAX
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Interface: -
• Other names: Q1376594

NOTES:
OPERATING CHARACTERISTICS
(Unless otherwise noted: --40°C ≤ T
Sensor Device Data
Freescale Semiconductor
Operating Range
Output Signal
Noise
Self--Test
Status
Output Stage Performance
Mechanical Characteristics
10. Preserves phase margin (60°) to guarantee output amplifier stability.
11. A measure of the device’s ability to reject an acceleration applied 90° from the true axis of sensitivity.
12. The Status pin output is not valid following power--up until at least one rising edge has been applied to the self--test pin. The Status pin is
13. The Status pin output latches high if the EPROM parity changes to odd. The Status pin can be reset by a rising edge on self--test, unless
1. For a loaded output the measurements are observed after an RC filter consisting of a 1 kΩ resistor and a 0.1 µF capacitor to ground.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 4.75 and 5.25 volts, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits
4. The device can measure both + and − acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
5. Sensitivity limits apply to 0 Hz acceleration.
6. At clock frequency ≅ 34 kHz.
7. The digital input pin has an internal pull--down current source to prevent inadvertent self test initiation due to external board level leakages.
8. Time for the output to reach 90% of its final value after a self--test is initiated.
9. Time for amplifiers to recover after an acceleration signal causing them to saturate.
Supply Voltage
Supply Current
Operating Temperature Range
Acceleration Range
Zero g (T
Zero g (V
Sensitivity (T
Sensitivity (V
Bandwidth Response
Nonlinearity
RMS (0.1 Hz -- 1.0 kHz)
Spectral Density (RMS, 0.1 Hz -- 1.0 kHz)
Output Response (V
Input Low
Input High
Input Loading
Response Time
Output Low (I
Output High (I
Electrical Saturation Recovery Time
Full Scale Output Range (I
Capacitive Load Drive
Output Impedance
Transverse Sensitivity
the device may operate as a linear device but is not guaranteed to be in calibration.
will increase above V
high whenever the self--test input is high.
a fault condition continues to exist.
(12)(13)
A
DD
= 25°C, V
= 5.0 V)
A
DD
(7)
load
load
(2)
= 25°C, V
(3)
(8)
= 5.0 V)
= 100 µA)
= --100 µA)
DD
DD
(10)
(11)
Characteristic
DD
= 5.0 V)
= 5.0 V)
DD
/2 and for negative acceleration the output will decrease below V
OUT
= 5.0 V)
= --200 µA)
(4)
A
≤ +105°C, 4.75 ≤ V
(5)
(9)
(6)
DD
≤ 5.25, Acceleration = 0g, Loaded output
Symbol
NL
V
t
n
∆V
DELAY
V
V
V
f
V
V
V
g
n
XZ,YZ
I
--3dB
V
V
t
T
RMS
I
C
Z
OFF
OFF
FSO
DD
S
S
ST
DD
FS
SD
IN
OH
OUT
OL
IH
A
IL
O
L
ST
V
V
0.7 V
DD
SS
−1.0
−40
1140
1110
−50
4.75
2.25
Min
V
1.1
2.2
0.3
40
—
—
—
—
—
—
—
—
—
+0.25
SS
−0.8
DD
DD
/2.
−125
1200
1200
5.00
(1)
Typ
500
2.2
1.5
2.5
2.5
5.0
0.6
—
50
—
—
—
10
—
—
—
—
—
50
—
)
V
0.3 V
DD
−300
+105
1260
1290
+1.0
Max
5.25
2.75
V
100
3.2
2.8
9.0
0.9
0.4
2.0
5.0
60
25
−0.25
—
—
—
—
DD
DD
MMA1260D
% FSO
µg/√Hz
% FSO
mVrms
mV/g
mV/g
Unit
mA
ms
ms
Hz
µA
°C
pF
Ω
V
V
V
V
V
V
V
V
V
g
3