MMA2201D Freescale Semiconductor, MMA2201D Datasheet - Page 3

• Manufacturer Part Number: MMA2201D
• Description: SENS ACCEL X-AXIS +-38G 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: MMAr

Specifications of MMA2201D

• Axis: X or Y
• Acceleration Range: ±45g
• Sensitivity: 50mV/g
• Voltage - Supply: 4.75 V ~ 5.25 V
• Output Type: Analog
• Bandwidth: 400Hz
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Sensing Axis: X
• Acceleration: 40 g
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MMA2201DTR; MMA2201DTR

Operating Characteristics
(Unless otherwise noted: –40°C ≤ T
NOTES:
Operating Range
Output Signal
Noise
Self-Test
Status
Minimum Supply Voltage (LVD Trip)
Clock Monitor Fail Detection Frequency
Output Stage Performance
Mechanical Characteristics
10. Preserves phase margin (60°) to guarantee output amplifier stability.
11. A measure of the device's ability to reject an acceleration applied 90° from the true axis of sensitivity.
12. The Status pin output is not valid following power-up until at least one rising edge has been applied to the self-test pin. The Status pin is high
13. The Status pin output latches high if a Low Voltage Detection or Clock Frequency failure occurs, or the EPROM parity changes to odd. The
Motorola Sensor Device Data
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 4.75 and 5.25 volts, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the
4. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
5. The device is calibrated at 20g.
6. At clock frequency ≅70 kHz.
7. The digital input pin has an internal pull-down current source to prevent inadvertent self test initiation due to external board level leakages.
8. Time for the output to reach 90% of its final value after a self-test is initiated.
9. Time for amplifiers to recover after an acceleration signal causing them to saturate.
1. For a loaded output the measurements are observed after an RC filter consisting of a 1 kΩ resistor and a 0.01 µF capacitor to ground.
Electrical Saturation Recovery Time
Full Scale Output Range (I
Capacitive Load Drive
Output Impedence
Supply Voltage
Supply Current
Operating Temperature Range
Acceleration Range
Zero g (T
Zero g
Sensitivity (T
Sensitivity
Bandwidth Response
Nonlinearity
RMS (10 Hz – 1 kHz)
Power Spectral Density
Clock Noise (without RC load on output)
Output Response
Input Low
Input High
Input Loading
Response Time
Output Low (I
Output High (I
Transverse Sensitivity
Package Resonance
device may operate as a linear device but is not guaranteed to be in calibration.
will increase above V
whenever the self-test input is high, as a means to check the connectivity of the self-test and Status pins in the application.
Status pin can be reset low if the self-test pin is pulsed with a high input for at least 100 µs, unless a fault condition continues to exist.
(12)(13)
A
= 25°C, V
A
load
(7)
load
(2)
= 25°C, V
(3)
(8)
= 100 µA)
= 100 µA)
DD
(10)
(11)
DD
= 5.0 V)
Characteristic
DD
/2 and for negative acceleration the output will decrease below V
OUT
= 5.0 V)
= 200 µA)
(4)
(5)
(9)
A
Freescale Semiconductor, Inc.
≤ +105°C, 4.75 ≤ V
For More Information On This Product,
(6)
Go to: www.freescale.com
DD
≤ 5.25, Acceleration = 0g, Loaded output.
Symbol
V
NL
t
V
V
n
DELAY
V
f
n
n
V
f
V
V
OFF,V
V
g
–3dB
g
V
f
XZ,YZ
I
V
PKG
S
RMS
t
C
Z
T
PSD
I
min
DD
OFF
CLK
LVD
FSO
ST
S
OH
DD
FS
OUT
ST
IN
OL
IH
IL
O
A
V
L
0.7 × V
0.46 V
V
DD
4.75
2.35
47.5
–1.0
Min
360
V
–30
150
0.25
−40
4.0
9.3
2.7
10
—
—
—
—
—
—
—
—
—
—
—
DD
SS
–0.8
DD
/2.
DD
0.50 V
–100
5.00
3.25
Typ
400
110
300
5.0
2.5
2.0
2.0
0.2
45
50
10
12
10
—
—
—
—
—
—
—
—
—
—
—
DD
(1)
)
V
0.54 V
0.3 × V
DD
+125
–300
Max
5.25
2.65
52.5
10.7
+1.0
V
440
400
100
6.0
2.8
0.4
4.0
5.0
—
—
—
14
10
—
—
—
—
DD
–0.25
DD
DD
µV/(Hz
mV/g/V
% FSO
% FSO
mVrms
MMA2201D
mVpk
mV/g
Unit
kHz
kHz
mA
Hz
µA
ms
ms
pF
Ω
V
C
V
V
V
V
V
V
V
V
g
g
1/2
)
3