MMA2202EGR2 Freescale Semiconductor, MMA2202EGR2 Datasheet - Page 3

• Manufacturer Part Number: MMA2202EGR2
• Description: SENSOR ACCEL X-AXIS 50G 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: MMAr

Specifications of MMA2202EGR2

• Axis: X or Y
• Acceleration Range: ±56.3g
• Sensitivity: 40mV/g
• Voltage - Supply: 4.75 V ~ 5.25 V
• Output Type: Analog
• Bandwidth: 400Hz
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Sensing Axis: X
• Acceleration: 50 g
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• No. Of Axes: 1
• Sensor Case Style: SOIC
• No. Of Pins: 16
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: -40°C To +125°C
• Acceleration Range ±: 50gf
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Sensors
Freescale Semiconductor
Table 2. Operating Characteristics
(Unless otherwise noted: –40°C ≤ T
10. The Status pin output latches high if a Low Voltage Detection or Clock Frequency failure occurs, or the EPROM parity changes to odd. The
11. Time for amplifiers to recover after an acceleration signal causes them to saturate.
12. Preserves phase margin (60°) to guarantee output amplifier stability.
13. A measure of the device's ability to reject an acceleration applied 90° from the true axis of sensitivity.
Operating Range
Output Signal
Noise
Self-Test
Status
Minimum Supply Voltage (LVD Trip)
Clock Monitor Fail Detection Frequency
Output Stage Performance
Mechanical Characteristics
1. For a loaded output the measurements are observed after an RC filter consisting of a 1 kΩ resistor and a 0.01 μF capacitor to ground.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 4.75 V and 5.25 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the
4. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
5. The device is calibrated at 20g.
6. At clock frequency ≅ 70 kHz.
7. The digital input pin has an internal pull-down current source to prevent inadvertent self test initiation due to external board level leakages.
8. Time for the output to reach 90% of its final value after a self-test is initiated.
9. The Status pin output is not valid following power-up until at least one rising edge has been applied to the self-test pin. The Status pin is
Supply Voltage
Supply Current
Operating Temperature Range
Acceleration Range
Zero g (T
Zero g
Sensitivity (T
Sensitivity
Bandwidth Response
Nonlinearity
RMS (10 Hz – 1 kHz)
Power Spectral Density
Clock Noise (without RC load on output)
Output Response
Input Low
Input High
Input Loading
Response Time
Output Low (I
Output High (I
Electrical Saturation Recovery Time
Full Scale Output Range (I
Capacitive Load Drive
Output Impedance
Transverse Sensitivity
Package Resonance
device may operate as a linear device but is not guaranteed to be in calibration.
will increase above V
high whenever the self-test input is high, as a means to check the connectivity of the self-test and Status pins in the application.
Status pin can be reset low if the self-test pin is pulsed with a high input for at least 100 μs, unless a fault condition continues to exist. For
a loaded output the measurements are observed after an RC filter consisting of a 1 kΩ resistor and a 0.01 μF capacitor to ground.
(9), (10)
A
= 25°C, V
A
(7)
load
(2)
load
= 25°C, V
(3)
(8)
= 100 μA)
= 100 μA)
DD
Characteristic
DD
(12)
(13)
= 5.0 V)
/2 and for negative acceleration the output will decrease below V
DD
OUT
= 5.0 V)
= 200 μA)
(4)
(5)
(11)
A
≤ +105°C, 4.75 ≤ V
(6)
DD
≤ 5.25, Acceleration = 0g, Loaded output.
Symbol
V
NL
t
V
DELAY
V
n
n
V
V
f
n
f
V
V
V
g
OFF,V
–3dB
g
VIH
f
XZ,YZ
I
PKG
V
t
T
S
RMS
C
Z
PSD
CLK
I
min
FSO
DD
OFF
LVD
S
ST
DD
IN
OH
FS
OUT
ST
OL
A
V
IL
O
L
0.7 x V
V
0.46V
DD
4.75
2.35
7.44
–1.0
Min
−40
360
V
–30
150
0.25
4.0
2.7
—
38
—
—
—
10
—
—
—
—
—
—
—
SS
–0.8
DD
D
DD
/2.
0.50 V
–100
5.00
56.3
3.25
Typ
400
110
300
5.0
2.5
2.0
2.0
0.2
40
12
10
—
—
—
—
—
—
—
—
—
—
—
8
DD
V
(1)
0.3 x V
0.54 V
DD
+125
–300
)
Max
5.25
2.65
8.56
+1.0
V
440
400
100
6.0
2.8
0.4
4.0
5.0
42
14
10
—
—
—
—
—
—
—
DD
–0.25
DD
DD
MMA2202KEG
μV/(Hz
mV/g/V
% FSO
mVrms
% FSO
mVpk
mV/g
Unit
kHz
kHz
mA
ms
ms
Hz
μA
pF
W
C
V
g
V
V
g
V
V
V
V
V
V
1/2
)
3