MMA7361LCR1 Freescale Semiconductor, MMA7361LCR1 Datasheet - Page 5

• Manufacturer Part Number: MMA7361LCR1
• Description: IC ACCELER 1.5/6G XYZ-AXIS 14LGA
• Manufacturer: Freescale Semiconductor

Specifications of MMA7361LCR1

• Package / Case: LGA-14
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): - 0.3 V
• Supply Current: 400 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package Type: LGA
• Operating Supply Voltage (min): 2.2V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 3mm
• Product Height (mm): 1mm
• Product Length (mm): 5mm
• Mounting: Surface Mount
• Pin Count: 14
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 4. Pin Descriptions
Pin No.
Sensors
Freescale Semiconductor
Pin Descriptions
10
11
12
13
14
1
2
3
4
5
6
7
8
9
Figure 5. Accelerometer with Recommended
V DD
Pin Name
0g-Detect
Self Test
g-Select
Sleep
X
Y
Z
0.1 μF
V
V
N/C
N/C
N/C
N/C
Logic
Input
NC
Logic
Input
Logic
Input
OUT
OUT
OUT
SS
DD
Figure 4. Pinout Description
X
Y
Z
N/C
V
OUT
OUT
OUT
V
DD
SS
Connection Diagram
10
13
No internal connection
Leave unconnected
X direction output voltage
Y direction output voltage
Z direction output voltage
Power Supply Ground
Power Supply Input
Logic input pin to enable product or Sleep Mode
No internal connection
Leave unconnected
Linear Freefall digital logic output signal
Logic input pin to select g level
Unused for factory trim
Leave unconnected
Unused for factory trim
Leave unconnected
Input pin to initiate Self Test
Unused for factory trim
Leave unconnected
6
5
7
g-Select
GND
V DD
V SS
Sleep
Top View
MMA7361LC
Sleep
N/C
0g-Delect
Z OUT
X OUT
Y OUT
Description
Self Test
N/C
N/C
g-Select
0g-Detect
N/C
9
2
3
4
3.3 nF
3.3 nF
3.3 nF
BASIC CONNECTIONS
PCB Layout
NOTES:
Figure 6. Recommended PCB Layout for Interfacing
1. Use 0.1 µF capacitor on V
2. Physical coupling distance of the accelerometer to
3. Place a ground plane beneath the accelerometer to
4. Use a 3.3 nF capacitor on the outputs of the
5. PCB layout of power and ground should not couple
6. Accelerometer and microcontroller should not be a
7. A/D sampling rate and any external power supply
8. 10 MΩ or higher is recommended on X
0g-Detect
source.
the microcontroller should be minimal.
reduce noise, the ground plane should be attached to
all of the open ended terminals shown in
accelerometer to minimize clock noise (from the
switched capacitor filter circuit).
power supply noise.
high current path.
switching frequency should be selected such that
they do not interfere with the internal accelerometer
sampling frequency (11 kHz for the sampling
frequency). This will prevent aliasing errors.
Z
relationship between the internal 32 kΩ resistor and
the measurement input impedance.
Self Test
g-Select
OUT
Sleep
X
Y
Z
V
V
OUT
OUT
OUT
DD
SS
Accelerometer to Microcontroller
to prevent loss due to the voltage divider
POWER SUPPLY
C
C
C
C
DD
C
C
to decouple the power
A/D
A/D
A/D
V
P0
P1
P2
P3
RH
IN
IN
IN
OUT
MMA7361LC
Figure
, Y
V
V
OUT
DD
SS
6.
and
C
C
5