MMA1260EG Freescale Semiconductor, MMA1260EG Datasheet - Page 3

• Manufacturer Part Number: MMA1260EG
• Description: SENSOR ACCEL Z-AXIS 1.5G 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: MMAr

Specifications of MMA1260EG

• Axis: Z
• Acceleration Range: ±1.5g
• Sensitivity: 1200 mV/g
• Voltage - Supply: 4.75 V ~ 5.25 V
• Output Type: Analog
• Bandwidth: 50Hz
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Sensing Axis: Z
• Acceleration: 1.5 g
• Supply Voltage (max): 7 V
• Supply Voltage (min): - 0.3 V
• Supply Current: 2.2 mA
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• For Use With: RD1986MMA2260D - KIT SENSOR ACCEL MMA2260D TRIAX
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Sensors
Freescale Semiconductor
Table 2. Operating Characteristics
(Unless otherwise noted: –40°C ≤ T
10. The Status pin output latches high if a Low Voltage Detection or Clock Frequency failure occurs, or the EPROM parity changes to odd. The
11. Time for amplifiers to recover after an acceleration signal causes them to saturate.
12. Preserves phase margin (60°) to guarantee output amplifier stability.
13. A measure of the device's ability to reject an acceleration applied 90° from the true axis of sensitivity.
1. For a loaded output the measurements are observed after an RC filter consisting of a 1 kΩ resistor and a 0.1 μF capacitor to ground.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 4.75 and 5.25 volts, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the
4. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
5. The device is calibrated at 1g. Sensitivity limits apply to 0Hz acceleration.
6. At clock frequency ≅70 kHz.
7. The digital input pin has an internal pull-down current source to prevent inadvertent self test initiation due to external board level leakages.
8. Time for the output to reach 90% of its final value after a self-test is initiated.
9. The Status pin output is not valid following power-up until at least one rising edge has been applied to the self-test pin. The Status pin is high
Operating Range
Output Signal
Noise
Self-Test
Status
Output Stage Performance
Mechanical Characteristics
device may operate as a linear device but is not guaranteed to be in calibration.
will increase above V
whenever the self-test input is high, as a means to check the connectivity of the self-test and Status pins in the application.
Status pin can be reset low if the self-test pin is pulsed with a high input for at least 100 μs, unless a fault condition continues to exist.
Supply Voltage
Supply Current
Operating Temperature Range
Acceleration Range
Zero g (T
Zero g (V
Sensitivity (T
Sensitivity (V
Bandwidth Response
Nonlinearity
RMS (0.1 Hz – 1.0 kHz)
Spectral Density (RMS, 0.1 Hz – 1.0 KHz)
Output Response (V
Input Low
Input High
Input Loading
Response Time
Output Low (I
Output High (I
Electrical Saturation Recovery Time
Full Scale Output Range (I
Capacitive Load Drive
Output Impedance
Transverse Sensitivity
(9), (10)
A
DD
= 25°C, V
= 5.0 V)
A
DD
(7)
load
load
(2)
= 25°C, V
(3)
(8)
= 5.0 V)
= 100 μA)
= 100 μA)
DD
DD
Characteristic
DD
(12)
(13)
= 5.0 V)
/2 and for negative acceleration the output will decrease below V
= 5.0 V)
DD
OUT
= 5.0 V)
= 200 μA)
(4)
A
(5)
(11)
≤ +105°C, 4.75 ≤ V
(6)
DD
≤ 5.25, Acceleration = 0g, Loaded output.
Symbol
NL
t
V
V
V
n
ΔV
DELAY
V
f
V
V
g
–3dB
n
V
XZ,YZ
I
V
V
t
T
RMS
C
Z
I
FSO
DD
OFF
OFF
S
S
ST
SD
IN
OH
DD
FS
OUT
OL
IH
A
IL
O
ST
L
V
V
0.7 V
SS
DD
1140
1110
–300
4.75
2.25
–1.0
Min
V
–40
1.1
2.2
0.3
40
—
—
—
—
—
—
—
—
—
+ 0.25
SS
– 0.8
DD
DD
/2.
1200
1200
–125
5.00
1.55
Typ
500
2.2
2.5
2.5
5.0
0.6
50
10
50
—
—
—
—
—
—
—
—
—
—
(1)
V
DD
0.3 V
)
+105
1260
1290
+1.0
Max
5.25
2.75
V
–50
100
3.2
2.8
9.0
0.9
0.4
2.0
5.0
60
25
—
—
—
—
– 0.25
DD
DD
MMA1260KEG
μg/
% FSO
% FSO
mVrms
mV/g
mV/g
Unit
mA
ms
ms
Hz
μA
°C
pF
Ω
V
g
V
V
V
V
V
V
V
V
Hz
3