DP83848I-MAU-EK/NOPB National Semiconductor, DP83848I-MAU-EK/NOPB Datasheet - Page 11
DP83848I-MAU-EK/NOPB
Manufacturer Part Number
DP83848I-MAU-EK/NOPB
Description
EVAL BOARD PHYTER IND TEMP
Manufacturer
National Semiconductor
Datasheet
1.DP83848I-MAU-EKNOPB.pdf
(84 pages)
Specifications of DP83848I-MAU-EK/NOPB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 11 of 84
- Download datasheet (4Mb)
1.3 Clock Interface
1.4 LED Interface
See Table 3 for LED Mode Selection.
X1
X2
25MHz_OUT
LED_LINK
LED_SPEED
LED_ACT/COL
Signal Name
Signal Name
S, O, PU
S, O, PU
S, O, PU
Type
Type
O
O
I
Pin #
Pin #
34
33
25
28
27
26
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock
reference input for the DP83848I and must be connected to a 25
MHz 0.005% (+50 ppm) clock source. The DP83848I supports ei-
ther an external crystal resonator connected across pins X1 and
X2, or an external CMOS-level oscillator source connected to pin
X1 only.
RMII REFERENCE CLOCK: This pin is the primary clock refer-
ence input for the RMII mode and must be connected to a 50 MHz
0.005% (+50 ppm) CMOS-level oscillator source.
CRYSTAL OUTPUT: This pin is the primary clock reference out-
put to connect to an external 25 MHz crystal resonator device.
This pin must be left unconnected if an external CMOS oscillator
clock source is used.
25 MHz CLOCK OUTPUT:
In MII mode, this pin provides a 25 MHz clock output to the sys-
tem.
In RMII mode, this pin provides a 50 MHz clock output to the sys-
tem.
This allows other devices to use the reference clock from the
DP83848I without requiring additional clock sources.
LINK LED: In Mode 1, this pin indicates the status of the LINK.
The LED will be ON when Link is good.
LINK/ACT LED: In Mode 2 and Mode 3, this pin indicates transmit
and receive activity in addition to the status of the Link. The LED
will be ON when Link is good. It will blink when the transmitter or
receiver is active.
SPEED LED: The LED is ON when device is in 100 Mb/s and OFF
when in 10 Mb/s. Functionality of this LED is independent of mode
selected.
ACTIVITY LED: In Mode 1, this pin is the Activity LED which is
ON when activity is present on either Transmit or Receive.
COLLISION/DUPLEX LED: In Mode 2, this pin by default indi-
cates Collision detection. For Mode 3, this LED output may be
programmed to indicate Full-duplex status instead of Collision.
11
Description
Description
www.national.com
Related parts for DP83848I-MAU-EK/NOPB
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
BOARD EVALUATION DP83848I
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
BOARD EVALUATION DP83848I
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal? Bus Transceiver
Manufacturer:
National Semiconductor
Datasheet: