IR3475MTR1PBF International Rectifier, IR3475MTR1PBF Datasheet - Page 5
IR3475MTR1PBF
Manufacturer Part Number
IR3475MTR1PBF
Description
IC BUCK SYNC ADJ 10A PQFN
Manufacturer
International Rectifier
Series
SupIRBuck™r
Type
Step-Down (Buck), PWM - Current Moder
Datasheet
1.IR3475MTRPBF.pdf
(21 pages)
Specifications of IR3475MTR1PBF
Internal Switch(s)
Yes
Synchronous Rectifier
Yes
Number Of Outputs
1
Voltage - Output
0.5 V ~ 12 V
Current - Output
10A
Frequency - Switching
Up to 750kHz
Voltage - Input
3 V ~ 27 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
*
Package / Case
*
Primary Input Voltage
27V
No. Of Outputs
1
Output Voltage
12V
Output Current
10A
No. Of Pins
17
Operating Temperature Range
-40°C To +125°C
Peak Reflow Compatible (260 C)
Yes
Rohs Compliant
Yes
Leaded Process Compatible
Yes
Part Status
Preferred
Package
PQFN / 4 x 5
Circuit
Single Output
Iout (a)
10
Switch Freq (khz)
0 - 750
Input Range (v)
3.0 - 27
Output Range (v)
0.5 - 12
Ocp Otp Uvlo Pre-bias Soft Start And
Constant On-Time + PGOOD + EN + Temp Comp OCP
Digital Home Media
Yes
Mobile Computing
Yes
Industrial 24v Input
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PIN DESCRIPTIONS
PIN #
4, 17
10
11
12
13
14
15
16
1
2
3
5
6
7
8
9
5
PIN NAME
PGOOD
3VCBP
PHASE
PGND
FCCM
BOOT
February 16, 2011 | ADVANCED DATASHEET | V1.8 | PD97602
GND
ISET
VCC
VIN
NC
NC
EN
FB
SS
FF
I/O LEVEL
Reference
Reference
VIN + VCC
3.3V
3.3V
3.3V
3.3V
VIN
VIN
VIN
5V
5V
5V
‐
‐
Forced Continuous Conduction Mode (CCM). Ground this pin to enable diode
emulation mode or discontinuous conduction mode (DCM). Pull this pin to 3.3V
to operate in CCM under all load conditions.
Connecting resistor to PHASE pin sets over current trip point.
Power good open drain output – pull up with a resistor to 3.3V
Bias return and signal reference.
Inverting input to PWM comparator, OVP / PGOOD sense.
Soft start/shutdown. This pin provides user programmable soft‐start function.
Connect an external capacitor from this pin to GND to set the startup time of the
output voltage. The converter can be shutdown by pulling this pin below 0.3V.
‐
For internal LDO. Bypass with a 1.0µF capacitor to AGND. A resistor in series with
the bypass capacitor may be required in single‐ground plane designs. Refer to
Layout Recommendation for details.
‐
VCC input. Gate drive supply. A minimum of 1.0µF ceramic capacitor is required.
Power return.
Phase node (or switching node) of MOSFET half bridge.
Input voltage for the system.
Bootstrapped gate drive supply – connect a capacitor to PHASE.
Input voltage feed forward – sets on‐time with a resistor to VIN.
Enable pin to turn on and off the device. Use two external resistors to set the
turn on threshold (see Electrical Specifications) for input voltage monitoring.
10A Highly Integrated SupIRBuck
PIN DESCRIPTION
TM
IR3475