AD7818ARM Analog Devices Inc, AD7818ARM Datasheet - Page 15
![IC ADC 10BIT W/TEMP SNSR 8-MSOP](/photos/1/38/13894/rm-8_sml.jpg)
AD7818ARM
Manufacturer Part Number
AD7818ARM
Description
IC ADC 10BIT W/TEMP SNSR 8-MSOP
Manufacturer
Analog Devices Inc
Datasheet
1.AD7817ARZ.pdf
(20 pages)
Specifications of AD7818ARM
Rohs Status
RoHS non-compliant
Function
Temp Monitoring System (Sensor)
Topology
ADC, Multiplexer, Register Bank
Sensor Type
Internal
Sensing Temperature
-40°C ~ 85°C
Output Type
MICROWIRE™, QSPI™, SPI™
Output Alarm
Yes
Output Fan
Yes
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
For Use With
EVAL-AD7816/7/8EB - BOARD EVALUATION FOR AD7816/7/8
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7818ARM
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7818ARMZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
POWER VS. THROUGHPUT
Superior power performance can be achieved by using the Auto-
matic Power-Down (Mode 2) at the end of a conversion (see
Operating Modes section of this data sheet).
Figure 18 shows how the Automatic Power-Down is imple-
mented to achieve the optimum power performance from the
AD7816, AD7817, and AD7818. The devices are operated in
Mode 2 and the duration of CONVST pulse is set to be equal to
the power-up time (2 µs). As the throughput rate of the device is
reduced the device remains in its power-down state longer, and
the average power consumption over time drops accordingly.
For example, if the AD7817 is operated in a continuous sam-
pling mode with a throughput rate of 10 kSPS, the power con-
sumption is calculated as follows. The power dissipation during
normal operation is 4.8 mW, V
2 µs and the conversion time is 9 µs, the AD7817 can be said to
dissipate 4.8 mW typically for 11 µs (worst case) during each
conversion cycle. If the throughput rate is 10 kSPS, the cycle
time is 100 µs and the power dissipated while powered up dur-
ing each cycle is (11/100) × (4.8 mW) = 528 µW typ. Power
dissipated while powered down during each cycle is (89/100) ×
(3 V × 2 µA) = 5.34 µW typ. Overall power dissipated is 528 µW
+ 5.34 µW = 533 µW.
REV. C
CONVST
BUSY
t
Figure 18. Automatic Power-Down
POWER-UP
2 s
CONVST
RD/ WR
BUSY
SCLK
D
t
OUT
CONVERT
OTI
D
CS
8 s
IN
100 s @ 10kSPS
t
CYCLE
DD
= 3 V. If the power up time is
DB7 – DB0
Figure 17. Mode 2 Operation
t
POWER-UP
–15–
t
3
AD7817 SERIAL INTERFACE
The serial interface on the AD7817 is a 5-wire interface with
read and write capabilities, with data being read from the output
register via the D
register via the D
requires an externally applied serial clock to the SCLK input to
access data from the data register or write to the control byte.
The RD/WR line is used to determine whether data is being
written to or read from the AD7817. When data is being written
to the AD7817, the RD/WR line is set logic low and when data
is being read from the part the line is set logic high (see Figure
20). The serial interface on the AD7817 is designed to allow the
part to be interfaced to systems that provide a serial clock that is
synchronized to the serial data, such as the 80C51, 87C51,
68HC11, 68HC05, and PIC16Cxx microcontrollers.
t
1
t
15
0.01
0.1
10
1
0
Figure 19. Power vs. Throughput Rate
t
16
10
OUT
IN
line. The part operates in a slave mode and
AD7816/AD7817/AD7818
20
line and data being written to the control
DB7(DB9) – DB0
THROUGHPUT – kHz
30
40
50
60
70
80