PC28F640J3D75B NUMONYX, PC28F640J3D75B Datasheet - Page 42
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
PC28F640J3D75B
Manufacturer Part Number
PC28F640J3D75B
Description
IC FLASH 64MBIT 75NS 64EZBGA
Manufacturer
NUMONYX
Datasheet
1.PC28F640J3D75E.pdf
(68 pages)
Specifications of PC28F640J3D75B
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
64M (8Mx8, 4Mx16)
Speed
75ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
872860
872860TR
872860TR
PC28F640J3D75 S L8QW
PC28F640J3D75B
872860TR
872860TR
PC28F640J3D75 S L8QW
PC28F640J3D75B
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PC28F640J3D75B
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Table 24: Valid Commands During Suspend (Sheet 2 of 2)
9.6
Table 25: STS Configuration Register
Notes:
1.
2.
Datasheet
42
Erase Suspend
Program/Erase Resume
Lock Block
Unlock Block
Program OTP Register
STS Configuration
In case of 256 Mb device (2x128), the command sequence must be repeated for each die at its base address
In case of 256 Mb device (2x128), keep the second cycle to the same address. (ie. Do not toggle A24 for the second cycle)
Command
During Suspend, array-read operations are not allowed in blocks being erased or
programmed.
A block-erase under program-suspend is not allowed. However, word-program under
erase-suspend is allowed, and can be suspended. This results in a simultaneous erase-
suspend/ program-suspend condition, indicated by SR[7,6,2] = 1.
To resume a suspended program or erase operation, issue the Resume command to
any device address. The read mode of the device is automatically changed to Read
Status Register. The operation continues where it left off, STS (in RY/BY# mode) goes
low, and the respective Status Register bits are cleared.
When the Resume command is issued during a simultaneous erase-suspend/ program-
suspend condition, the programming operation is resumed first. Upon completion of the
programming operation, the Status Register should be checked for any errors, and
cleared. The resume command must be issued again to complete the erase operation.
Upon completion of the erase operation, the Status Register should be checked for any
errors, and cleared.
Status Signal (STS)
The STATUS (STS) signal can be configured to different states using the STS
Configuration command
remains in that configuration until another Configuration command is issued or RP# is
asserted low. Initially, the STS signal defaults to RY/BY# operation where RY/BY# low
indicates that the WSM is busy. RY/BY# high indicates that the state machine is ready
for a new operation or suspended.
To reconfigure the STATUS (STS) signal to other modes, the Configuration command is
given followed by the desired configuration code. The three alternate configurations are
all pulse mode for use as a system interrupt as described in the following paragraphs.
For these configurations, bit 0 controls Erase Complete interrupt pulse, and bit 1
controls Program Complete interrupt pulse. Supplying the 0x00 configuration code with
the Configuration command resets the STS signal to the default RY/BY# level mode.
Device Command
Device Address
Address Bus
(Table
Setup Write Cycle
1
25). Once the STS signal has been configured, it
Table 26
Program Suspend
00B8h
Not Allowed
Not Allowed
Not Allowed
Not Allowed
Data Bus
Allowed
displays possible STS configurations.
Numonyx™ Embedded Flash Memory (J3 v. D)
Device Address
Address Bus
Confirm Write Cycle
2
Erase Suspend
Not Allowed
Not Allowed
Not Allowed
Not Allowed
Allowed
Register Data
November 2007
Data Bus
308551-05