68175-5RFX AMPHENOL RF, 68175-5RFX Datasheet - Page 5

• Manufacturer Part Number: 68175-5RFX
• Description: CONN BNC PLUG CRIMP RG59 (20AWG)
• Manufacturer: AMPHENOL RF
• Series: BNC, RFXr
• Type: Cable Plugr

Specifications of 68175-5RFX

• Connector Style: BNC, RFX
• Connector Type: Plug, Male Pins
• Contact Termination: Crimp, Dual
• Impedance: 50 Ohm
• Mounting Type: Free Hanging (In-Line)
• Fastening Type: Bayonet Lock
• Cable Group: RG-59, Belden 1505A, 9100
• Frequency - Max: 4GHz
• Frequency-max: 4GHz
• Body Style: Straight Plug
• Coaxial Termination: Crimp
• Rg Cable Type: RG-59
• Contact Material: Brass
• Contact Plating: Gold
• Frequency Max: 4GHz
• Angle: Straight
• Application: Commercial
• Cable Type: RG-59/U,RG/U 59
• Finish, Housing: Nickel
• Gender: Plug
• Material, Contact: Brass
• Material, Dielectric: TFE
• Material, Housing: Brass
• Mating Type: Bayonet
• Primary Type: BNC
• Special Features: 3-Pc
• Temperature, Operating: -65 to +165 °C
• Termination: Crimp
• Voltage, Rating: 500 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Color: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 68-175-5RFX; 68175-5RFX1; ARFX1046

Assembly Instructions-C26b
BNC
ORIGINAL CRIMP PLUGS
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Amphenol Corporation Tel: [phone]
Amphenol
Number
31-351
31-359
31-371
lip of boot must be firmly posi-
tioned in body groove
Connector
BNC Plug
BNC Plug
BNC Plug
Type
note: center conductor must
be visible thru contact solder
hole prior to soldering
boot
outer ferrule must
clamp nut assy
as shown
58, 141
59, 62, 140
174, 179, 187, 188, 316
outer ferrule
boot
RG-/U
Cable
a
b
cable dielectric must
butt insulator as shown
c
ferrule
Cavity for
Contact
—
—
—
302
nut assembly
Step 1 Install boot and slide outer ferrule onto cable as shown prior
Step 2 Strip cable jacket, braid and dielectric to dimensions shown.
Step 3 Slightly flare out end of cable braid as so as to facilitate
Step 4 Install ferrule clamp nut assembly onto cable so that ferrule
Step 5 Soft solder center conductor to contact using rosin core per
Step 6 Screw connector body onto prepared cable termination .
Step 7 Push body forward and into position as shown to complete
ferrule clamp
* for pneumatic crimp tool 227-60, use die sets indicated in this column
Hex Crimp Data
Outer Ferrule
Cavity for
.213(5.4)
.255(6.5)
.128(3.2)
to stripping cable.
See attached table for dimensions. All cuts are to be sharp
and square. Important: DO NOT nick braid, dielectric, and
center conductor when cutting. Tin center conductor using
soft solder per QQ-S-571 comp Sn 60. Avoid excessive heat
while tinning to prevent swelling of cable dielectric.
insertion onto ferrule clamp nut assembly. Important:
DO NOT comb out braid.
portion slides under braid and insulator butts flush against
cable dielectric. Slide outer ferrule over braid and up
against nut. Make sure no slack exists in braid. Crimp outer
ferrule with tool specified in table above, keeping cable
dielectric bottomed against insulator.
QQ-S-571 comp Sn 60. DO NOT get any solder on outside
surfaces of contact.
Wrench tighten by holding the cable nut assembly
STATIONARY while ROTATING the connector body.
assembly.
plug body assembly
Tool 227-944*
Die Set for
227-1221-11
227-1221-13
227-1221-3
.922(23.4)
.922(23.4)
.797(20.2)
Stripping Dimensions, inches (mm)
a
Amphenol
.516(13.1)
.516(13.1)
.516(13.1)
www.amphenolrf.com
b
.250(6.3)
.250(6.3)
.250(6.3)
c
®