DEBB33A682KN7A Murata Electronics North America, DEBB33A682KN7A Datasheet - Page 71

• Manufacturer Part Number: DEBB33A682KN7A
• Description: CAP 1000VDC
• Manufacturer: Murata Electronics North America
• Series: DEBr

Specifications of DEBB33A682KN7A

• Voltage - Rated: 1000V (1kV)
• Lead Style: *
• Capacitance: 6800pF
• Tolerance: ±10%
• Temperature Coefficient: B
• Mounting Type: *
• Operating Temperature: -25°C ~ 85°C
• Features: High Voltage
• Applications: General Purpose
• Package / Case: *
• Size / Dimension: *
• Thickness: *
• Lead Spacing: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -

!Note
Operating Temperature Range: -40 to +125 C
No.
* "Room condition" Temperature: 15 to 35 C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
1
2
3
4
5
6
7
8
9
Safety Standard Certified Type KJ for Automotive Specifications and Test Methods
Appearance and Dimensions
Marking
Capacitance
Dissipation Factor (D.F.)
Insulation Resistance (I.R.)
Dielectric
Strength
Temperature Characteristics
Solderability
Resistance to
Soldering
Heat
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
Item
Between Lead
Wires
Body
Insulation
Appearance
Capacitance
Change
I.R.
Dielectric
Strength
No visible defect, and dimensions are within
specified range.
To be easily legible
Within specified tolerance
10000M min.
No failure
No failure
Lead wire should be soldered with uniform coating
on the axial direction over 3/4 of the circumferential
direction.
No marked defect
Within 10%
1000M min.
Per Item 6
(Temp. range: -25 to +85 C)
Char.
Char.
B, E
B
E
Capacitance Change
Specifications
Specifications
Within
Within 10%
D.F.V2.5%
+20
–55
%
Type KJ Specifications and Test Methods
The capacitor should be visually inspected for evidence of
defect.
Dimensions should be measured with slide calipers.
The capacitor should be visually inspected.
The dissipation factor should be measured at 20˚C with
1 0.1kHz and AC5V(r.m.s.) max.
The insulation resistance should be measured with
The voltage should be applied to the capacitor through a
resistor of 1M .
The capacitor should not be damaged when the test voltages
from Table 1 are applied between the lead wires for 60 sec.
First, the terminals of the capacitor
should be connected together. Then,
as shown in the figure at right, a metal
foil should be closely wrapped around
the body of the capacitor to the
distance of about 3 to 4mm from
each terminal.
Then, the capacitor should be inserted
into a container filled with metal balls
of about 1mm diameter. Finally, AC
voltage from Table 2 is applied for 60 sec. between the
capacitor lead wires and metal balls.
The capacitance measurement should be made at each step
specified in Table 3.
Pre-treatment:
Should be placed into steam aging for 8 hrs. 15 min. After the
steam aging, the lead wire of a capacitor should be dipped into
an ethanol solution of 25% rosin and then into molten solder for
5+0/-0.5 sec.
The depth of immersion is up to about 1.5 to 2.0mm from the
root of lead wires.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245 5 C
As shown in the figure, the lead
wires should be immersed in
solder of 260 5 C up to 1.5 to
2.0mm from the root of terminal for
10 1 sec.
Pre-treatment:
Post-treatment:
DC500 50V within 60 5 sec. of charging.
Capacitor should be stored at 125 3 C for 1 hr., then placed
at room condition* for 24 2 hrs. before initial measurements.
Capacitor should be stored at
125 3 C for 1 hr., then placed at room condition* for 24 2
hrs. before initial measurements.
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Type
Type
Step
KJ
KJ
1
2
3
4
5
H63 Eutectic Solder 235 5 C
<Table 1>
<Table 2>
<Table 3>
AC2600V(r.m.s.)
AC2600V(r.m.s.)
Temperature (ºC)
Test Voltage
Test Voltage
Test Method
-25 2
20 2
20 2
85 2
20 2
Continued on the following page.
Thermal
Screen
Metal
Foil
Capacitor
about
3 to 4mm
Metal
Balls
Molten
Solder
1.5
to 2.0mm
69
C85E.pdf
Jul.13,2011
12