DEHR33D102KN3A Murata Electronics North America, DEHR33D102KN3A Datasheet - Page 72

• Manufacturer Part Number: DEHR33D102KN3A
• Description: CAP CER 2000VDC R RAD
• Manufacturer: Murata Electronics North America
• Series: DEHr

Specifications of DEHR33D102KN3A

• Voltage - Rated: 2000V (2kV)
• Lead Style: *
• Capacitance: 1000pF
• Tolerance: ±10%
• Temperature Coefficient: R
• Mounting Type: *
• Operating Temperature: -25°C ~ 125°C
• Features: High Voltage, Low Dissipation Factor
• Applications: General Purpose
• Package / Case: *
• Size / Dimension: *
• Thickness: *
• Lead Spacing: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -

12
!Note
70
No.
10 Vibration
11
12
13
14
* "Room condition" Temperature: 15 to 35 C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Type KJ Specifications and Test Methods
Safety Standard Certified Type KJ for Automotive Specifications and Test Methods
Continued from the preceding page.
Mechanical
Shock
Humidity
(Under
Steady
State)
Humidity
Loading
Life
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
D.F.
Appearance
Capacitance
D.F.
I.R.
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
D.F.
I.R.
Appearance
Capacitance
Change
I.R.
Dielectric
Strength
No marked defect
Within the specified tolerance
No marked defect
Within the specified tolerance
10000M min.
No marked defect
3000M min.
Per Item 6
No marked defect
3000M min.
No marked defect
Within 20%
3000M min.
Per Item 6
Char.
Char.
Char.
Char.
Char.
Char.
B, E
B, E
B, E
B, E
B
E
B
E
Capacitance Change
Capacitance Change
Specifications
Specifications
Specifications
Specifications
Specifications
Within 10%
Within 15%
Within 10%
Within 15%
D.F.V2.5%
D.F.V5.0%
D.F.V5.0%
D.F.V5.0%
Solder the capacitor and gum
up the body to the test jig
(glass epoxy board) by resin
(adhesive).
The capacitor should be firmly soldered to the supporting lead
wire, 1.5mm in total amplitude, with about a 20 minutes rate of
vibration change from 10Hz to 2000Hz and back to 10Hz.
This motion should be applied 12 times in each of 3 mutually
perpendicular directions (total of 36 times).
The acceleration is 5g max.
Solder the capacitor and gum
up the body to the test
jig (glass epoxy board) by
resin (adhesive).
Three shocks in each direction should be applied along 3
mutually perpendicular axes to and from of the test specimen
(18 shocks).
The specified test pulse should be half-sine and should have a
duration: 0.5ms, peak value: 100g and velocity change: 4.7m/s.
Set the capacitor for 1000 12 hrs. at 85 3 C in 80 to 85%
relative humidity.
Pre-treatment:
Post-treatment:
Apply the rated voltage for 1000 12 hrs. at 85 3 C in 80 to
85% relative humidity.
Pre-treatment:
Post-treatment:
Impulse Voltage
Each individual capacitor should be subjected to a 5kV
impulses for three times. Then the capacitors are applied to life
test.
Apply a voltage from Table 4 for 1000 hrs. at 125+2/-0 C, and
relative humidity of 50% max.
Pre-treatment:
Post-treatment:
Capacitor should be stored at 125 3 C for 1hr., then placed
at room condition* for 24 2 hrs. before initial measurements.
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Capacitor should be stored at 125 3 C for 1hr., then placed
at room condition* for 24 2 hrs. before initial measurements.
Capacitor should be stored for 1 to 2 hrs. at room condition.*
Capacitor should be stored at 125 3 C for 1hr., then placed
at room condition* for 24 2 hrs. before initial measurements.
Capacitor should be stored for 1 to 2 hrs. at room condition.*
0
100 (%)
90
50
30
AC510V(r.m.s.), except that once each hour the voltage
is increased to AC1000V(r.m.s.) for 0.1 sec.
T
T
1
T
2
Applied Voltage
Test Method
<Table 4>
t
Continued on the following page.
Front time (T
Time to half-value (T
1
) =1.2 s=1.67T
Resin (Adhesive)
Resin (Adhesive)
2
) =50 s
C85E.pdf
Jul.13,2011