H7CX-AW-N-AC100-240 Omron, H7CX-AW-N-AC100-240 Datasheet - Page 41
![Tachometers ScrwNon-conf 12VDC,6dig, SPDTout](/photos/18/6/180612/h7cx-n_sml.jpg)
H7CX-AW-N-AC100-240
Manufacturer Part Number
H7CX-AW-N-AC100-240
Description
Tachometers ScrwNon-conf 12VDC,6dig, SPDTout
Manufacturer
Omron
Type
1 or 2 State, Total and Preset Counterbatch, Dual/Twin Counterr
Datasheet
1.H7CX-A-N_AC100-240.pdf
(56 pages)
Specifications of H7CX-AW-N-AC100-240
Frequency Response
50 Hz
Product
Panel Mount Tachometer
Voltage
100 VAC to 240 VAC
Display Type
6 Digit
Accuracy
+/- 0.1 %
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
AC100240 H7CXAWN
Nomenclature
Dimensions
Tachometers
Dimensions with Front Connecting Socket
H7CX-R@-N
Dimensions without Flush Mounting Adapter
H7CX-R@-N
Dimensions with Flush Mounting Adapter (Adapter and
Waterproof Packing Ordered Separately)
H7CX-R@-N
1. Hold Indicator (orange)
2. Key Protect Indicator (orange)
3. Control Output Indicator (orange)
4. Comparison Value 1, 2 Stage Indicator
5. Present Value (Main Display)
6. Comparison Value (Sub-display)
(Lit when the hold input or hold key is ON. )
Lit when the key protect switch is ON.
Character height: 10 mm (red)
Character height: 6 mm (green)
Character Size
for Main Display
OUT 1
OUT
(1-output models)
Display Section
10 mm
2
(2-output models)
58
Character Size
for Sub-display
48
48
6 mm
48
Y92S-29 (order separately)
Waterproof Packing
6
H7CX-R@-N
(51)
7.5
10
2
3
1
7
8
Panel
63.7
100.9
103.2*
P2CF-11(-E) (order separately)
Front Connecting Socket
Y92F-30 (order separately)
Flush Mounting Adapter
6th digit
89.9
14.4
44.8
1st digit
44.8
* These dimensions vary with the kind of DIN track (reference value).
P3GA-11
(order
separately)
Rear Surface
Connection
Socket
11
5
6
4
9
Panel Cutouts
Panel cutouts are as shown below
(according to DIN43700).
Note:
7. Mode Key
8. Hold Key
9. Up Keys
10. Key-protect Switch
11. DIP Switch
(Factory setting) OFF
(Used to switch mode and setting items.)
(Used to sustain the measurement value and output.)
OFF
(Factory setting)
ON
1.
2.
3.
The mounting panel thickness should be 1 to 5 mm.
To allow easier operation, it is recommended that
Adapters be mounted so that the gap between
sides with hooks is at least 15 mm (i.e., with the
panel cutouts separated by at least 60 mm).
It is possible to mount counters side by side, but
only in the direction without the hooks. If Counters/
Tachometers are mounted side by side, however,
water resistance will be lost.
60 min.
(Disable)
With Y92A-48F1 attached.
With Y92A-48 attached.
1 2 3 4 5 6 7 8
A={48n 2.5+(n 1) 4}
A=(51n 5.5)
Operation Keys
15 min.
n side by side mounting
1
45
Switches
+0.6
to
0
A=(48n 2.5)
6
A
45
+1
+0.6
ON
(Enable)
0
0
H7CX-R@-N
60 min.
+1
0
+1
0
(Unit: mm)
41