DMS-30PC-1-GL-C Murata Power Solutions Inc, DMS-30PC-1-GL-C Datasheet - Page 2
![Digital Panel Meters 3.5 Digit +-2V Input Low Power Grn](/photos/18/5/180582/dms30pc0bsc_sml.jpg)
DMS-30PC-1-GL-C
Manufacturer Part Number
DMS-30PC-1-GL-C
Description
Digital Panel Meters 3.5 Digit +-2V Input Low Power Grn
Manufacturer
Murata Power Solutions Inc
Type
3 1/2 Digit, LED Display Low-Powerr
Datasheet
1.DMS-30PC-1-GS-C.pdf
(6 pages)
Specifications of DMS-30PC-1-GL-C
Equipment Type
3 1/2 Digit, LED Display Low-Power
Input
+/- 2 V
Display Type
3 - 1/2 Digit LED
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
DMS-30PC-1-GL-C
Performance/Functional Specifi cations
Typical at T
circuit, unless otherwise noted.
➀ Applies for transient or continuous overvoltages applied to (+) INPUT HI (pin 11) with
➁ See Technical Notes.
Analog Inputs
Full Scale Input Range:
Input Impedence:
Overvoltage Protection ➀
Common Mode Voltage Range
CMRR (dc to 60Hz)
Control Inputs ➁
Decimal Point Placement (Pins 4-6)
Display Test (Pin 2)
Performance
Sampling Rate
Accuracy (3 minute warm-up):
Zero Reading (Vin = 0 Volts)
Temperature Drift (0 = +60°C)
+1.23V Reference Output (Pin 9) ➁
Power Supply Requirements
Supply Voltage
Supply Current:
Display
Display Type and Size
Polarity Indication
Overrange Indication
Physical/Environmental
Operating Temperature
Storage Temperature
Humidity (non-condensing)
Case Material
Weight
DMS-30PC-0
DMS-30PC-1
DMS-30PC-2
DMS-30PC-3
DMS-30PC-0, -1
DMS-30PC-2, -3
DMS-30PC-0 (Vin = +0.19V)
DMS-30PC-1 (Vin = +1.9V)
DMS-30PC-2 (Vin = +19V)
DMS-30PC-3 (Vin = +190V)
Standard Models
Low-Power Models
(–) INPUT LO (pin 12) properly connected. Pin 12 is not overvoltage protected
(see Figure 1). Voltages applied to pin 12 should not exceed the supply voltage.
Red Display
Green or Orange Display
A
= +25°C and supply voltage = +5V using the single-ended input
“–001”
+1.20
Tie to pin 3 to activate
Tie to +5V to activate all segments
+4.75
Min.
–40
100
0.8
3½ digit, 0.56"/14.2mm high LED
Autopolarity ("–" for negative Vin)
–
–
–
–
–
–
–
–
–
–
–
–
–
0
0
–
–
–
"–1_ _ _" for negative inputs
"1_ _ _ " for positive inputs
0.75 ounces (21 grams)
2.5 reading per second
www.murata-ps.com/dpm
“000”
+1.23
+5.00
+150
+12
+60
±200
±200
1000
±0.2
Typ.
±20
Polycarbonate
±2
±1
±1
±2
±2
86
1
–
–
–
–
–
+5.25
+225
+17
+100
“001”
+1.25
±250
Max.
±0.4
+60
+75
±2
±3
±3
±3
±3
95
–
–
–
–
–
–
–
Volts
Cnts/°C
Counts
Counts
Counts
Counts
Units
Volts
Volts
Volts
Volts
Volts
Volts
MΩ
MΩ
mA
mA
mA
mV
dB
°C
°C
%
TECHNICAL NOTES
Ordering Information
1. +1.23V REFERENCE OUTPUT (Pin 9): This pin is the output
2. ANALOG COMMON (Pin 10): This pin is connected to an internal,
3. REFERENCE OUTPUT (Pin 8) and INPUT (Pin 7): Pin 8 is a preci-
Input Range:
DMS-30PC - 1 - R S - C
Accessories:
Add-On Application Boards:
of the meter’s precision +1.23V internal reference, and it is
referenced to ANALOG COMMON (pin 10) which sits at a potential
of approximately +2V. This output should be buffered if used to
drive external loads since sourcing more than 15μA from pin 9 can
affect both the initial accuracy and temperature drift of the meter.
low-noise, "relative" ground. It is used in certain differential and
"fl oating" measurements as described in the Applications section
of this data sheet and Ap Note 3 of the DATEL Panel Meter Catalog.
Pin 10 should not be connected to pin 3 (5V RETURN) or to your
system’s analog ground.
sion reference actively trimmed at the factory. In normal opera-
tion, pin 8 must be tied to pin 7 to achieve all listed accuracy and
drift specifi cations.
±200V available on the
following models only:
-BS (Super Blue)
-GS (Standard Green)
-RS (Standard Red)
-RL (Low-Power Red)
-VFS (Blue-Green)
0 = ±200mV
1 = ±2V
2 = ±20V
3 = ±200V
DMS-30-CP
DMS-BZL1-C
DMS-BZL2-C
DMS-EB-C
DMS-EB-HTB
DMS-EB-DC/DC
DMS-EB-RMS-C
DMS-EB-AC/DC-C For ac line-powered applications
A panel-mount retaining clip is supplied with each model.
Technical enquiries email: sales@murata-ps.com, tel:
3½ Digit, LED Display Low-Power,
Miniature Digital Panel Voltmeters
Panel cutout punch
DMS-30 bezel assembly
DMS-30 bezel assembly with sealing gasket
Multi-purpose (gain/offset, 4-20mA, etc.)
High-accuracy temperature probe sensing for
±200mV models
Provides isolated +5V power
For true rms measurements of ac voltages
DMS-30PC Series
LED Color:
AS = Standard Amber
BS = Super Blue
GS = Standard Green
OS = Standard Orange
QS = Standard Aqua
RS = Standard Red
YS = Standard Yellow
RH = High-Intensity Red
GL = Low-Power Green
OL = Low-Power Orange
RL = Low-Power Red
VFS = Blue-Green
MPM_DMS_30PC.F05 Page 2 of 6
Add -C for RoHS
+1 508 339 3000