MEA1D1205SC Murata Power Solutions Inc, MEA1D1205SC Datasheet - Page 4

• Manufacturer Part Number: MEA1D1205SC
• Description: DC/DC Converters & Regulators 12Vin +/-5Vout +/-100mA 1W
• Manufacturer: Murata Power Solutions Inc
• Series: MEAr

Specifications of MEA1D1205SC

• Output Power: 0.5 W
• Input Voltage Range: 10.8 V to 13.2 V
• Input Voltage (nominal): 12 V
• Number Of Outputs: 2
• Output Voltage (channel 1): 5 V
• Output Current (channel 1): 100 mA
• Output Voltage (channel 2): - 5 V
• Output Current (channel 2): - 100 mA
• Isolation Voltage: 1 KV
• Package / Case Size: SIP
• Output Type: Isolated Dual
• Output Voltage: +/- 5 V
• Package / Case: SIP
• Product: Isolated
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATION NOTES
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test confi guration.
Differential Mode Noise Test Schematic
C1
C2
C3
R1
R2
T1
RLOAD
Measured values are multiplied by 10 to obtain the specifi ed values.
MEA1D0505xC
MEA1D0509xC
MEA1D0512xC
MEA1D0515xC
MEA1D1205xC
MEA1D1209xC
MEA1D1212xC
MEA1D1215xC
MEA1D1505xC
MEA1D1509xC
1μF X7R m ultilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
than 100mΩ at 100 kHz
100nF multilayer ceramic capacitor, general purpose
450Ω resistor, carbon fi lm, ±1% tolerance
50Ω BNC termination
3T of the coax cable through a ferrite toroid
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Start-up time
10810
2872
5325
8895
1150
3716
6912
3160
939
883
μs
SUPPLY
MEA1D1512xC
MEA1D1515xC
MEA1D2405xC
MEA1D2409xC
MEA1D2412xC
MEA1D2415xC
MEA1D4805xC
MEA1D4809xC
MEA1D4812xC
MEA1D4815xC
DC/DC Converter
Input
+
-
Output
+
-
Start-up time
C1 C2 C3
5630
8585
1473
2643
4348
1705
2995
4722
472
586
μs
R LOAD
R1
T1
1kVDC Isolated 1W Dual Output DC/DC Converters
Technical enquiries email: [e-mail], tel: [phone]
R2
OSCILLOSCOPE
Y INPUT
Typical Start-Up Wave Form
2010-07-08 KDC_MEA1.C03 Page 4 of 8
MEA1 Series