A6TR-6101 Omron, A6TR-6101 Datasheet - Page 3

• Manufacturer Part Number: A6TR-6101
• Description: DIP Switches / SIP Switches 6 Pin, Thru-Hole Flat, Low Profile
• Manufacturer: Omron

Specifications of A6TR-6101

• Switch Type: DIP
• Actuator: Piano
• Terminal Pitch: 2.54 mm
• Termination Style: Through Hole
• Current Rating: 25 mAmps
• Operating Temperature Range: - 20 C to + 70 C
• Number Of Positions: 6
• Contact Configuration: SPST-CO
• No. Of Switch Positions: 6
• Actuation Type: Piano Key
• Pitch Spacing: 2.54mm
• Contact Current Dc Max: 25mA
• Switch Mounting: Through Hole
• Svhc: No SVHC (15-Dec-2010)
• Contact Rating: 25 mAmps
• Actuator Style: Piano Key
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Installation
Safety Precautions
Observe the following conditions when soldering the A6TR/A6SR.
Make sure that the lever of A6TR/A6SR is set fully to OFF. Misalign-
ment may result in reduced sensitivity due to the soldering heat.
Observe the following conditions for reflow soldering the A6SR.
(Measurement location: Top of Switch)
Soldering temperature: 260°C max. (Preheatine: 150°C • 120 s max.)
Soldering time: 5 s max.
The A6TR/A6SR cannot be washed. Attempting to wash it may result
in malfunction due to flux and foreign matter from the PCB flowing
into the A6TR/A6SR together with the cleaning fluid.
The type of flux or the amount or method in which it is applied,
including its use in reflow soldering, can have adverse effects on
Switch performance. Assess the proper flux, conditions, and meth-
ods prior to using it.
The "RoHS Compliant" designation indicates that the listed models
do not contain the six hazardous substances covered by the RoHS
Directive.
Reference: The following standards are used to determine compli-
ance for the six substances.
To prevent discoloration of the terminals and other problems during
storage, do not store the A6TR/A6SR in locations subject to the
following conditions.
Also, the A6TR/A6SR is not waterproof or splash-resistant. Do not
install or use the A6TR/A6SR in locations that are subject to contact
with water.
Do not subject the A6TR/A6SR to freezing or condensation.
3
• General Precautions for Soldering
• Reflow Soldering (A6SR)
• Automatic Soldering Bath (A6TR)
• Lead: 1,000 ppm max.
• Mercury: 1,000 ppm max.
• Cadmium: 100 ppm max.
• Hexavalent chromium: 1,000 ppm max.
• PBB: 1,000 ppm max.
• PBDE: 1,000 ppm max.
Soldering
Washing
Using Flux
RoHS Compliant
Environment for Storage and Use
1. High temperatures or humidity
2. Corrosive gases
3. Direct sunlight
260 max.
Internal Connections (Top View)
ON
230
180
150
2
DIP Switch (Piano Type)
9 0
Preheating
60 to 150
Actual
soldering
60 max.
Time (s)
A6TR/A6SR
Do not apply excessive operating force to the Switch. Otherwise the
Switch may be damaged or deformed, and the switch mechanism
may malfunction as a result. Apply an operating force not exceeding
7.8 N. (Operate the actuator one operation at a time. Do not operate
the Switch from the top of actuator. Otherwise the actuator may be
damaged, so operate the Switch from the lower part of the actuator.)
Note:
Dimensions
A±0.3
B±0.15
C
D
E
A
DIP Switch operation
Packing Specifications
E
The perforations along both sides are for Switches with 8
and 10 poles.
1.5
Perforations
B
+0.15
-0.05
C
No of poles
dia.
D
16
2
±
±
0.15
(22)
0.15
7.5
5.4
16
2
(5.8)
11.5
10.5
(30)
24
---
4
330
±
Tape drawing
direction
2 dia.
P=4
1.75
11.5
15.6
(30)
24
6
±
±
0.15
0.15
14.2
20.7
28.4
(38)
Tape drawing
direction
32
8
20.2
25.7
40.4
(50)
10
44