D4B-1116N Omron, D4B-1116N Datasheet - Page 14

• Manufacturer Part Number: D4B-1116N
• Description: Basic / Snap Action / Limit Switches Adjustable Lever PG13.5 1NC/1NO
• Manufacturer: Omron

Specifications of D4B-1116N

• Contact Form: NO / NC
• Contact Rating: 2 Amps
• Actuator: Lever, Roller
• Operating Force: 9.41 N
• Termination Style: Screw
• Actuation Type: Adjustable Roller Lever
• Operating Force Max: 960gf
• Switch Operation: Snap Action
• Contact Voltage Ac Max: 600V
• Contact Current Ac Max: 10A
• Switch Terminals: Screw
• Svhc: No SVHC (15-Dec-2010)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

D4B-jN
Mounting
Use four M5 screws with washers to mount the standard model. Be
sure to apply the proper torque to tighten each screw. The D4B-jN
can be mounted more securely by using the four screws plus two
5
height of 4.8 mm as shown below.
Mounting Dimensions (M5)
Changes in Actuator Mounting Position
To change the angle of the lever, loosen the hexagon-head bolts on
the side of the lever.
The operation indicator plate has protruding parts which engage
with the lever, thus allowing changes to the lever position by 90 .
The back of the operation indicator plate has no protruding parts.
The lever can be set at any angle by attaching the operation indica-
tor plate to the Switch so that this side will face the lever. In this case,
however, the D4B-jN will not be approved by SUVA or BIA. Make
sure that the lever engages with the operation indicator plate se-
curely so that the lever will not slip.
Changes in Head Mounting Position
By removing the screws on the four corners of the head, the head
can be reset in any of four directions. Make sure that no foreign ma-
terials will penetrate through the head.
Wiring
Do not connect the bare lead wires directly to the terminals but be
sure to connect each of them by using an insulation tube and M3.5
round solderless terminals and tighten each terminal screw within
the specified torque range.
The proper lead wire is 20 to 14 AWG (0.5 to 2.5 mm
14
–0.05
/
30
–0.15
dz dia.:
D dia.:
B:
L:
F:
I:
Standard Model
-mm protruding parts, each of which has a maximum
3.7
4.5
7.0
20.2
7.7
9.0 (mm)
60
59.3 0.1
D dia.
3-conduit Model
27 0.1
Protruding portions
5
30
40
42
–0.05
–0.15
dia. holes, max. 5 height
dz dia.
2
) in size.
Make sure that all solderless terminals come into contact with the
casing or cover as shown below, otherwise the cover may not be
mounted properly or the D4B-jN may malfunction.
Connector
Make sure that each connector is tightened within the specified
torque range. The casing may be damaged if the connector is tight-
ened excessively.
If the 1/2-14NPT is used, cover the cable and conduit end with seal-
ing tape in order to ensure IP67.
The Pg13.5 connector must be Nippon Flex’s ABS-08Pg13.5 or
ABS-12 Pg13.5.
Use OMRON’s SC-series connector which is suited to the cable in
diameter.
Properly attach the provided conduit cap to the unused conduit
opening and securely tighten the cap screw within the specified
torque when wiring the D4B-jN.
Crimp-style
terminal
Crimp-style terminal
Case
Correct
Correct
Crimp-style terminal
Terminal screw
Terminal screw
Cover
Case
Crimp-style terminal
Incorrect
Incorrect
Terminal screw
Cover
Crimp-style terminal
D4B-jN