G6Z-1PE-DC24 Omron, G6Z-1PE-DC24 Datasheet - Page 13
![Low Signal Relays - PCB NL 24VDC 75 Ohm E terminal 2.6GHz](/photos/17/55/175553/g6zt_sml.jpg)
G6Z-1PE-DC24
Manufacturer Part Number
G6Z-1PE-DC24
Description
Low Signal Relays - PCB NL 24VDC 75 Ohm E terminal 2.6GHz
Manufacturer
Omron
Series
G6Zr
Datasheet
1.G6Z-1FE-A-DC12.pdf
(16 pages)
Specifications of G6Z-1PE-DC24
Contact Form
1 Form C
Coil Voltage
24 VDC
Coil Current
8.3 mA
Coil Type
Non-Latching
Power Consumption
200 mW
Termination Style
Solder Pin
Isolation
60 dB to 65 dB at 900 MHz / 30 dB to 45 dB at 2.6 GHz
Insertion Loss
0.1 dB to 0.2 dB at 900 MHz / 0.3 dB to 0.5 dB at 2.6 GHz
Maximum Switching Current
0.5 A
Contact Rating
30 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
G6Z-1PE-DC24V
Manufacturer:
OMRON
Quantity:
12 000
Packaging
1. Tube Packaging
Relays in tube packaging are arranged so that the orientation mark
of each Relay in on the left side.
Be sure not to make mistakes in Relay orientation when mounting
the Relay to the PCB.
Tube length: 530 mm (stopper not included)
No. of Relays per tube: 25
2. Tape and Reel Packaging (Surface mount
Terminal Models)
When ordering Relays in tape packing, add the prefix “-TR” to the
model number, otherwise the Relays in stick packing will be provided.
Relays per Reel: 300
Direction of Relay Insertion
Recommended Soldering Method
■ Temperature Conditions for IRS Method
When using reflow soldering, ensure that the Relay terminals and the
top of the case stay below the following curve. Check that these
conditions are actually satisfied before soldering the terminals.
Top of case
Measured
Terminals
part
Stopper (gray)
Carrier tape
T4
T3
T2
T1
150 → 180°C,
(T1 → T2, t1)
Preheating
Operation of Relays
120 s max.
Top tape
(cover tape)
---
Emboss
tape
Preheating
230°C min,
t
Soldering
1
30 s max.
(T3, t2)
---
Pulling direction
Soldering Time
t
2
Stopper (green)
Orientation mark
Maximum peak
250°C max.
255°C max.
(T4)
Pulling
direction
Reel Dimensions
Carrier Tape Dimensions
Note: The radius of the unmarked corner is 0.3 mm.
Do not quench the terminals after mounting. Clean the Relay using
alcohol or water no hotter than 40°C max.
The thickness of cream solder to be applied should be between
150 and 200 μm on OMRON’s recommended PCB pattern.
Check the soldering in the actual mounting conditions before use.
2
5° max.
PCB
±0.1
Correct Soldering
10.2
4
16
±0.1
4
±0.1
±0.1
±0.1
Terminal
Relay
1.5
Solder
Land
High-frequency Relay
+ 0.1
0
A
dia.
A
Incorrect Soldering
330
Enlarged view of A
0.2
R0.75
80
1.75
14.2
1.5
+ 0.1
0
Insufficient
amount of
solder
±0.1
±0.1
28.4
1.7
±0.1
+ 0.15
0
32
33.5
37.5
±0.3
2
±0.5
G6Z
±1
±1
Enlarged view of A
22.6
5° max.
13
±0.1
0.5
20.6
±0.2
±0.05
dia.
±0.1
Excessive
amount of
solder
21
10
±0.8
±0.1
353
R1
dia.