G6Z-1PE-DC5 Omron, G6Z-1PE-DC5 Datasheet - Page 14
![Low Signal Relays - PCB NL 5VDC 75 Ohm E terminal 2.6GHz](/photos/17/55/175553/g6zt_sml.jpg)
G6Z-1PE-DC5
Manufacturer Part Number
G6Z-1PE-DC5
Description
Low Signal Relays - PCB NL 5VDC 75 Ohm E terminal 2.6GHz
Manufacturer
Omron
Series
G6Zr
Specifications of G6Z-1PE-DC5
Contact Form
1 Form C
Coil Voltage
5 VDC
Coil Current
40 mA
Coil Type
Non-Latching
Power Consumption
200 mW
Termination Style
Solder Pin
Isolation
60 dB to 65 dB at 900 MHz / 30 dB to 45 dB at 2.6 GHz
Insertion Loss
0.1 dB to 0.2 dB at 900 MHz / 0.3 dB to 0.5 dB at 2.6 GHz
Maximum Switching Current
0.5 A
Coil Frequency Max
2.6GHz
Coil Voltage Vdc Nom
5V
Contact Current Max
500mA
Contact Voltage Ac Nom
30V
Contact Voltage Dc Nom
30V
Coil Resistance
125ohm
Contact Configuration
SPDT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
G6Z
Stick Packing and Tape Packing
Stick Packing
Relays in stick packing are arranged so that the orientation mark
of each Relay in on the left side.
Be sure not to make mistakes in Relay orientation when mounting
the Relay to the PCB.
Stick length: 530 mm (stopper not included)
No. of Relays per stick: 25
Tape Packing (Surface-mounting Terminal
Models)
When ordering Relays in tape packing, add the prefix “-TR” to the
model number, otherwise the Relays in stick packing will be pro-
vided.
Relays per Reel: 300
Direction of Relay Insertion
Recommended Soldering Method
Temperature Conditions for IRS Method
When using reflow soldering, ensure that the Relay terminals and
the top of the case stay below the following curve. Check that
these conditions are actually satisfied before soldering the termi-
nals.
Terminals
Top of case
Measured
part
Stopper (gray)
Carrier tape
T4
T3
T2
T1
150 → 180 ° C,
120 s max.
---
(T1 → T2, t1)
Operation of Relays
Preheating
Top tape
(cover tape)
Emboss
tape
Preheating
230 ° C min,
30 s max.
---
t
Soldering
1
(T3, t2)
Pulling direction
Soldering Time
t
2
Stopper (green)
Orientation mark
250 ° C max.
255 ° C max.
Maximum
peak
(T4)
Pulling
direction
Reel Dimensions
Carrier Tape Dimensions
Note:
Do not quench the terminals after mounting. Clean the Relay
using alcohol or water no hotter than 40 ° C max.
The thickness of cream solder to be applied should be between
150 and 200 µ m on OMRON’s recommended PCB pattern.
Check the soldering in the actual mounting conditions before use.
5° max.
PCB
2
±0.1
Correct Soldering
10.2
4
16
4
±0.1
The radius of the unmarked corner is 0.3 mm.
±0.1
±0.1
±0.1
Terminal
Relay
1.5
Solder
+ 0.1
Land
0
A
dia.
A
Incorrect Soldering
330
Enlarged view of A
0.2
R0.75
80
1.5
1.75
14.2
+ 0.1
0
Insufficient
amount of
solder
±0.1
±0.1
28.4
1.7
±0.1
+ 0.15
0
32
33.5
37.5
±0.3
2
±0.5
±1
±1
Enlarged view of A
22.6
5° max.
13
±0.1
0.5
20.6
±0.2
±0.05
dia.
±0.1
Excessive
amount of
solder
21
10
G6Z
±0.8
±0.1
R1
131
dia.