SFECV10M7KA00-R0 Murata, SFECV10M7KA00-R0 Datasheet - Page 38

• Manufacturer Part Number: SFECV10M7KA00-R0
• Description: Filters SFECV10M7KA00-R0
• Manufacturer: Murata
• Type: Ceramic Filterr

Specifications of SFECV10M7KA00-R0

• Product: Ceramic Filters
• Frequency: 10.7 MHz
• Impedance: 330 Ohms
• Operating Temperature Range: - 20 C to + 80 C
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
The component cannot be withstand washing.
1. Do not use this product with bend. The component
2. The component may be damaged when an excess stress
3. All kinds of re-flow soldering must not be applied
4. Do not clean or wash the component as it is not
5. Do not use strong acidity flux, more than 0.2wt%
may be damaged if excess mechanical stress is
applied to it mounted on the printed circuit board.
will be applied.
on the component.
hermetically sealed.
Loaded Resistance and Waveform (Rg+R1=330ohm)
Loaded Capacitance and Waveform (Rg+R1=R2=330ohm)
Notice (Soldering and Mounting)
Notice (Handling)
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
10.5
10.5
10.5
10.5
10.6
10.6
10.6
Frequency (MHz)
10.6
Frequency (MHz)
Frequency (MHz)
Frequency (MHz)
R
R
C=10pF
C=56pF
2
2
10.7 10.8 10.9
10.7 10.8 10.9
=220
10.7 10.8 10.9
=560
10.7 10.8 10.9
SFELA10M7GA00-B0
SFELA10M7GA00-B0
1.2
1.0
0.8
0.6
0.4
0.2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
10.5
10.5
10.5
10.5
10.6
Frequency (MHz)
10.6
Frequency (MHz)
10.6
Frequency (MHz)
10.6
Frequency (MHz)
R
C=33pF
C=82pF
R
2
2
=330
10.7 10.8 10.9
10.7 10.8 10.9
10.7 10.8 10.9
10.7 10.8 10.9
=1k
Lead Type CERAFILr Characteristics Data and Notice
1.2
1.0
0.8
0.6
0.4
0.2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
6. In case of covering discriminator with over coat,
7. Accurate test circuit values are required to
chlorine content, in flow soldering.
conditions such as material of resin, cure
temperature, and so on should be evaluated well.
measure electrical characteristics. It may be a
cause of mis-correlation if there is any deviation,
especially stray capacitance, from the test
circuit in the specification.
P61E7.pdf 01.10.17
37
10