BLM18PG471SN1D Murata, BLM18PG471SN1D Datasheet - Page 197
![EMI/RFI Suppressors & Ferrites 470 OHM](/photos/16/33/163388/lpmuratablm_sml.jpg)
BLM18PG471SN1D
Manufacturer Part Number
BLM18PG471SN1D
Description
EMI/RFI Suppressors & Ferrites 470 OHM
Manufacturer
Murata
Type
Chip Beadr
Specifications of BLM18PG471SN1D
Shielding
Unshielded
Test Frequency
100 MHz
Product
Chip Ferrite Beads
Impedance
470 Ohms
Tolerance
25 %
Maximum Dc Current
1000 mAmps
Maximum Dc Resistance
0.2 Ohms
Operating Temperature Range
- 55 C to + 125 C
Package / Case
0603 (1608 metric)
Termination Style
SMD/SMT
Dc Resistance Max
0.2ohm
Dc Current Rating
1A
Ferrite Mounting
SMD
Ferrite Case Style
0603 / 1608
Rohs Compliant
Yes
Inductance
Not RequireduH
Core Material
Ferrite
Tolerance (+ Or -)
25%
Dc Resistance
200mOhm
Case Size (inches)
0603in
Operating Temp Range
-55C to 125C
Dc Current
1A
Product Diameter (mm)
Not Requiredmm
Product Height (mm)
0.95mm
Product Depth (mm)
0.8mm
Product Length (mm)
1.75mm
Military Standard
Not Required
Failure Rate
Not Required
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BLM18PG471SN1D
Manufacturer:
Phihong
Quantity:
2 300
Company:
Part Number:
BLM18PG471SN1D
Manufacturer:
MURATA
Quantity:
32 000
Part Number:
BLM18PG471SN1D
Manufacturer:
MURATA/村田
Quantity:
20 000
!Note
Block Type EMIFILr
1. Cleaning
2. Soldering
3. Other
<Operating Environment>
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
Do not use products in the environment close to the
organic solvent.
<Storage and Handling Requirements>
1. Storage Period
2. Storage Conditions
Do not use products beyond the rated current and rated
voltage as this may create excessive heat and
deteriorate the insulation resistance.
(1) Storage temperature: -10 to +40˚C
(2) Do not store products in a chemical atmosphere
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
Storage and Operating Conditions
Do not clean BNX series (SMD Type).
Before cleaning, please contact Murata engineering.
Reliability decreases with improper soldering methods.
Please solder by the standard soldering conditions
shown in mounting information.
Noise suppression levels resulting from Murata's EMI
suppression filters EMIFILr may vary, depending on
the circuits and ICs used, type of noise, mounting
pattern, mounting location, and other operating
conditions. Be sure to check and confirm in advance
the noise suppression effect of each filter, in actual
circuits, etc. before applying the filter in a commercial-
purpose equipment design.
BNX series should be used within 12 months.
Solderability should be checked if this period is
exceeded.
Notice (Soldering and Mounting)
Rating
Relative humidity: 15 to 85%
Avoid sudden changes in temperature and humidity.
such as chlorine gas, acid or sulfide gas.
SMD Type
!Caution/Notice
!Caution
Notice
1. Resin Coating
2. Handling of a Substrate (for BNX02p)
Bending
Handling
Using resin for coating/molding products may affect
the products performance.
So please pay careful attention in selecting resin.
Prior to use, please make the reliability evaluation with
the product mounted in your application set.
After mounting products on a substrate, do not apply
any stress to the product caused by bending or
twisting to the substrate when cropping the substrate,
inserting and removing a connector from the substrate
or tightening screw to the substrate.
Excessive mechanical stress may cause cracking in
the Product.
Twisting
195
Mar.28,2011
C31E.pdf